Deutz-Fahr Agroplus 60 / 70 / 80 service schedule

1. Wipe each nipple clean before and after.
2. Grease each point shown in your handbook.
3. Grease again after a high-pressure wash to push the water out.

Tools: Grease gun, Rag

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out.
2. Replace the filters as the handbook shows and top the oil up to the mark.
3. Run the engine, check for leaks and recheck the level.

Tools: Strap wrench, Drain tray, Shop towels

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out.
2. Check the level in the reservoir and top up to MAX with the same fluid only.
3. A falling level means a leak: have it checked before you work the tractor.

Tools: Clean funnel, Rags

1. Engine off, key out. Look for cracks, fraying and oil on the belt.
2. Check the tension as the handbook says and replace a worn belt.

Tools: Torch

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out. Warm the engine first, then let it settle. Hot oil burns, so wear gloves.
2. Put the tray under the sump, undo the drain plug and let all the oil run out.
3. Unscrew the old filter cartridge and throw it away. Wipe the seat clean.
4. Smear the new cartridge's seal with clean engine oil and fit it as the handbook says.
5. Refit the drain plug with a new washer. Fill with about 9.5 L (Agroplus 60) or 11 L (70, 80) of 15W-40, plus about 1 L for the filter, and check the dipstick.
6. Run the engine for a few minutes, stop it, wait a minute and recheck the level and for leaks.
7. Take the old oil and filter to a proper disposal point.

Tools: Drain tray (15 L), Socket set and spanners, Oil filter strap wrench, Funnel, Gloves, Shop towels

1. Stop the engine and let it cool. No flames or smoking. Put a container under the filter.
2. Undo the old filter, wipe the seat clean, oil the seal on the new filter and screw it on by hand.
3. Bleed the air as your handbook shows, start the engine and check for leaks.

Tools: Strap wrench, Container for fuel, Shop towels

1. Have a dealer check the clearance with the engine stopped for at least 2 hours.

Tools: Feeler gauges, Torque wrench

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out. Warm the oil by working the tractor first.
2. Drain the transmission and rear axle housing at the drain plugs.
3. Replace the oil filters.
4. Refit the plugs and fill with about 41 L of UTTO to the level mark.
5. Run the engine, work the hydraulics, stop and recheck the level.

Tools: Drain trays or drums (about 50 L), Socket set, Funnel and filler pump, Gloves

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out.
2. Drain the centre housing and each side reduction gear, then refit the plugs.
3. Refill the centre housing with ≈6 L and each side reduction gear with ≈1.5 L to the level plugs.

Tools: Drain tray, Socket set, Oil pump

1. Park on level ground, stop the engine, set the parking brake, lower any implement and take the key out.
2. Drain the PTO housing, change the filter cartridge and clean the wire-mesh filter.
3. Refit the plug and fill with about 2.5 L of UTTO to the level mark.

Tools: Drain tray, Socket set, Shop towels

1. Stop the engine and open the air filter housing.
2. Lift out the main cartridge and clean it as the handbook shows. Never clean the safety cartridge, replace it.
3. Replace the safety cartridge after 3 cleanings of the main one or 2 years.
4. Wipe the housing out, refit and close it properly.

Tools: Clean cloth, Low-pressure compressed air