Fendt 700 and 800 Vario COM3 service schedule
Fendt 800 Vario · c. 2007–2010 (Eurol, for the 818 Vario COM3); check your serial number
Covers the Fendt 700 and 800 Vario COM3 (712, 714, 716, 718, 818, 820).
Every maker's service job for the Fendt 700 and 800 Vario COM3, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.
Track your 700 and 800 Vario COM3 for freeVersions: 712, 714, 716 Vario; 718, 818, 820 Vario (more oil in the transmission and final drives)
Service intervals
| Job | When |
|---|---|
| Engine oil and filter change | every 500 hours or every year |
| Lubricate all grease points | every 500 hours |
| Fuel filter and pre-filter change | every 1,000 hours |
| Engine air filter elements | every 1,000 hours |
| Belts, idler, tensioner, water pump and fan bearings check | every 1,000 hours |
| Vario transmission oil and filters change | every 1,000 hours |
| Front axle differential and hub oil change | every 1,000 hours |
| Hydraulic oil and filters change | every 1,000 hours |
| Cab air filters | every 1,000 hours |
| Engine coolant change | every 2,000 hours |
| Valve clearance check | every 2,000 hours |
| Rear axle final drive oil change | every 2,000 hours |
| Front PTO oil and filter change (if fitted) | every 2,000 hours |
Service jobs and parts
Engine oil and filter change
Engine · every 500 hours or every year
Dealer schedule: engine oil, oil filter and drain plug gasket are changed together at every 500-hour service. Eurol lists a 12-month limit for the 818 COM3.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Engine oil | 1 | 15W-40. Engine oil, 17 L (Eurol lists 16.5 L for the 818 COM3). Aztec Oils match: EMPROTEC EHPD 15W-40 | 79038710B |
| Engine oil filter | 1 | The seal supplied in the box should be white | F716200510020 |
| Sump drain plug gasket | 1 | X540005678000 |
Step-by-step
- Park on level ground, lower the linkage and any implement, stop the engine, take the key out and chock the wheels.
- Warm the engine first so the oil drains well, then let it stand a few minutes. Hot oil burns, so wear gloves.
- Remove the sump drain plug and let the oil drain fully.
- Remove the old oil filter and clean the filter seat. Wipe a little clean oil on the new seal and fit the filter as it says on the filter.
- Fit the drain plug with a new gasket and tighten it to the torque in your handbook.
- Fill with the oil in the notes, run the engine for a minute, stop, wait a few minutes and check the dipstick. Top up to the mark, not above.
- Check for leaks at the filter and plug.
Tools: Drain tray (large enough for the sump), Filter wrench, Spanner or socket for the sump plug, Funnel, Rags, Gloves
Lubricate all grease points
Chassis · every 500 hours
Dealer schedule: all grease points on the lubrication chart at every 500-hour service, including the front axle driveline.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Grease | 1 | Lithium grease for the front axle driveline; dealer grease pack 79014728B. Grade for the other points: check your handbook | 79014728B |
Step-by-step
- Wipe each grease nipple clean.
- Pump in grease from your handbook's lubrication chart until fresh grease just shows.
- Wipe off the excess, which only collects dirt.
Tools: Grease gun, Rags
Fuel filter and pre-filter change
Fuel · every 1,000 hours
Dealer schedule: fuel filter and fuel pre-filter every 1,000 hours. Drain water from the pre-filter when needed (the dealer lists this at the 1,500-hour check).
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fuel filter | 1 | F731200060020 | |
| Fuel pre-filter | 1 | F842201060010 |
Step-by-step
- Park on level ground, lower the linkage and any implement, stop the engine and take the key out. No naked flames.
- Clean around the filter housings so no dirt gets in when they are opened.
- Remove the old filters and catch what spills. Dispose of it properly.
- Wipe the seats clean, fit the new O-rings from the box and fit the new filters.
- Bleed or prime the system as your handbook says, start the engine and check for leaks.
Tools: Filter wrench or the key the handbook shows, Clean rags, Gloves, Container for spilled fuel
Engine air filter elements
Engine · every 1,000 hours
Dealer schedule: outer and inner elements are replaced every 1,000 hours. At the 1,500-hour service the dealer cleans them out and replaces only if needed (older numbers 72311033 outer, 72317849 inner).
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Primary (outer) air filter | 1 | H515200090100 | |
| Secondary (inner) air filter | 1 | H716200090110 |
Step-by-step
- Stop the engine and take the key out. Never run the engine with the filter out.
- Open the air cleaner housing and take out the outer element, then the inner one.
- Wipe the inside of the housing with a damp cloth. Do not blow dirt down the intake.
- Fit the new elements and close the housing, checking the seals sit evenly.
- Check the intake hoses and clips for chafing or leaks.
Tools: Torch, Damp cloth
Belts, idler, tensioner, water pump and fan bearings check
Engine · every 1,000 hours
Dealer schedule: remove the belts and check the idler and tensioner bearings every 1,000 hours. Water pump bearings (weep hole) and fan bearings are checked at every 500-hour service.
Step-by-step
- Stop the engine and take the key out. Let it cool.
- Carry out the check or change as your handbook describes.
- Replace or adjust anything that is worn or out of limits.
- Run the engine and check that everything works.
Tools: Basic hand tools, Torch, Rags
Vario transmission oil and filters change
Transmission · every 1,000 hours
Dealer schedule: transmission oil, pressure filter, suction filter and drain plug gaskets all every 1,000 hours. Eurol lists 2,000 hours / 24 months for the 818 COM3; the dealer's shorter interval is used here.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission oil | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook). 43 L on 712, 714 and 716, and 48 L on 718, 818 and 820 (dealer notes; the dealer's pack quantity is 48 L). Aztec Oils match: AGRITEC UTTO | 79035451B |
| Pressure filter | 1 | F91610060001A | |
| Pressure filter O-ring | 1 | 72313495 | |
| Suction filter | 1 | F916100490010 | |
| Suction filter O-ring | 1 | 72424095 | |
| Drain plug gasket | 2 | Dealer lists 2 | X540008278000 |
| Drain plug gasket (second size) | 1 | X540010278000 |
Step-by-step
- Park on level ground, lower the linkage and implements, stop the engine, take the key out and chock the wheels.
- Clean around the drain plugs, filters and filler before opening anything.
- Drain the oil from the plugs the handbook shows. Warm oil drains best, but take care, it is hot.
- Change the filters and O-rings listed, wetting the new seals with clean oil.
- Refit the drain plugs with new gaskets, then fill with the oil in the notes.
- Run the engine, work the controls, then stop and check the level. Top up to the mark. Check for leaks.
Tools: Drain tray (large), Spanners and sockets for plugs and filter housings, Filter wrench, Funnel or pump, Rags, Gloves
Front axle differential and hub oil change
Front axle · every 1,000 hours
Dealer schedule: front differential oil, hub oil and their gaskets every 1,000 hours. Check the toe-in at each 500-hour service: 0 to 1 mm (0 to 0.04 in).
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Front axle differential oil | 1 | 80W-90. Gear oil, 9 L (dealer quantity; Eurol lists 8.3 L). Aztec Oils match: TRANSMATEC EP-4 80W-90 | 79036959B |
| Differential seal (dealer lists with the oil) | 2 | Dealer lists 2 | 742508 |
| Differential drain plug gasket | 2 | X540007678000 | |
| Front hub oil | 1 | 80W-90. Gear oil, 3 L (dealer quantity). Aztec Oils match: TRANSMATEC EP-4 80W-90 | 79036959B |
| Hub gasket | 2 | X540009678000 |
Step-by-step
- Park on level ground, stop the engine, take the key out and chock the wheels. Warm oil drains best.
- Clean around the filler and drain plugs. Remove the filler plug first so you know you can refill it.
- Remove the drain plugs and let the oil run out. Clean any magnetic plugs.
- Fit the drain plugs with new gaskets or O-rings.
- Fill through the filler hole to the level in your handbook. Wait a few minutes and check again.
- Refit the filler plug and check for leaks after a short drive.
Tools: Drain tray, Spanner or socket for the drain and fill plugs, Pump or funnel for gear oil, Rags, Gloves
Hydraulic oil and filters change
Hydraulics · every 1,000 hours
Dealer schedule: hydraulic oil, vent filter, return filter, control pressure filter and the end plate / accumulator job all every 1,000 hours. At the same job the dealer checks the hydraulic unlock coil: no more than 4.7 ohms.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Hydraulic oil | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook), 46 L (Eurol lists 50 L for the 818 COM3). Aztec Oils match: AGRITEC UTTO | 79037113B |
| Hydraulic return filter | 1 | O-ring is 72312305 | G716860060310 |
| Hydraulic vent filter | 1 | X820001191000 | |
| Control pressure filter | 1 | Dealer gives no number: check your handbook | check your handbook |
| Drain plug O-ring | 1 | X548842900000 | |
| Dipstick O-ring | 1 | 568-114 | |
| End plate service part | 1 | Dealer job: service end plate / test accumulator. O-rings 72433580 and 72433582 | F716961020220 |
| End plate service part (second) | 1 | F716961020330 |
Step-by-step
- Park on level ground, lower the linkage and implements, stop the engine, take the key out and chock the wheels.
- Clean around the drain plugs, filters and filler before opening anything.
- Drain the oil from the plugs the handbook shows. Warm oil drains best, but take care, it is hot.
- Change the filters and O-rings listed, wetting the new seals with clean oil.
- Refit the drain plugs with new gaskets, then fill with the oil in the notes.
- Run the engine, work the controls, then stop and check the level. Top up to the mark. Check for leaks.
Tools: Drain tray (large), Spanners and sockets for plugs and filter housings, Filter wrench, Funnel or pump, Rags, Gloves
Cab air filters
Cab · every 1,000 hours
Dealer schedule: fresh air, recirculating and heater filters every 1,000 hours. Check them at the 1,500-hour service and replace if dirty (older numbers 72478600 fresh air, 72478606 heater, 72426606 foam).
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fresh air filter | 2 | Dealer lists 2 | H816810140071 |
| Recirculating air filter | 2 | Dealer lists 2 | 920810140040 |
| Heater air filter | 1 | H716810130011 |
Step-by-step
- Stop the engine and take the key out.
- Take out the old filters, noting which way they face.
- Clean the housings, then fit the new filters the same way round.
- Refit the covers.
Tools: Basic hand tools, Rags
Engine coolant change
Cooling · every 2,000 hours
Dealer schedule: coolant and its drain plug gasket every 2,000 hours. Eurol lists 24 months for the 818 COM3.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Coolant | 1 | Premixed Fleetguard antifreeze, 19 L | CC2826 |
| Coolant drain plug gasket | 1 | X540002478000 |
Step-by-step
- Stop the engine and let it cool completely. Never open a hot cooling system.
- Open the radiator or expansion cap slowly, then drain the coolant from the drain plug into a tray.
- Fit the drain plug with a new gasket.
- Refill with the coolant in the notes, run the engine up to temperature with the heater on full and top up.
- Dispose of old coolant properly. Never pour it on the ground.
Tools: Drain tray (large), Hoses or funnel, Rags, Gloves
Valve clearance check
Engine · every 2,000 hours
Dealer schedule: valve clearance checked every 2,000 hours. The dealer gives no figures for this generation: check your handbook.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Valve cover gasket | 1 | F712201210020 |
Step-by-step
- Stop the engine and take the key out. Let it cool.
- Carry out the check or change as your handbook describes.
- Replace or adjust anything that is worn or out of limits.
- Run the engine and check that everything works.
Tools: Basic hand tools, Torch, Rags
Rear axle final drive oil change
Rear axle · every 2,000 hours
Dealer schedule: final drive oil and drain plug gaskets every 2,000 hours. The level is checked at the 1,000 and 1,500-hour services. The dealer gives no pack number for this oil.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Final drive oil | 1 | 85W-140. Gear oil, 11 L on 712, 714 and 716; 13 L on 718, 818 and 820 (dealer notes). Aztec Oils match: AGRITEC EP-4 85W-140 WBS | check your handbook |
| Drain plug gasket | 4 | Dealer lists 4 | X540009478000 |
Step-by-step
- Park on level ground, stop the engine, take the key out and chock the wheels. Warm oil drains best.
- Clean around the filler and drain plugs. Remove the filler plug first so you know you can refill it.
- Remove the drain plugs and let the oil run out. Clean any magnetic plugs.
- Fit the drain plugs with new gaskets or O-rings.
- Fill through the filler hole to the level in your handbook. Wait a few minutes and check again.
- Refit the filler plug and check for leaks after a short drive.
Tools: Drain tray, Spanner or socket for the drain and fill plugs, Pump or funnel for gear oil, Rags, Gloves
Front PTO oil and filter change (if fitted)
Front axle · every 2,000 hours
Dealer schedule: front PTO oil, filter and gaskets every 2,000 hours. The level is checked at the 1,000 and 1,500-hour services.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Front PTO oil | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook), 4 L. Aztec Oils match: AGRITEC UTTO | 79037113B |
| Front PTO filter | 1 | O-ring is 72376561 | 716150200160 |
| Front PTO gasket | 2 | Dealer lists 2 | X540008278000 |
| Front PTO gasket (second part) | 1 | X548926666000 |
Step-by-step
- Park on level ground, lower the linkage and implements, stop the engine, take the key out and chock the wheels.
- Clean around the drain plugs, filters and filler before opening anything.
- Drain the oil from the plugs the handbook shows. Warm oil drains best, but take care, it is hot.
- Change the filters and O-rings listed, wetting the new seals with clean oil.
- Refit the drain plugs with new gaskets, then fill with the oil in the notes.
- Run the engine, work the controls, then stop and check the level. Top up to the mark. Check for leaks.
Tools: Drain tray (large), Spanners and sockets for plugs and filter housings, Filter wrench, Funnel or pump, Rags, Gloves
Oils, fluids and capacities
| System | Oil or spec | Capacity |
|---|---|---|
| Engine | Deutz TCD 2012 L06 4V six-cylinder turbo diesel (Eurol, for the 818 Vario COM3) | |
| Engine oil | 15W-40. Engine oil (dealer pack 79038710B). Check your handbook for the Fendt/engine maker's specification. | 17 L with filter (dealer schedule); Eurol lists 16.5 L for the 818 |
| Coolant | Premixed Fleetguard antifreeze (dealer part CC2826), 19 L (dealer schedule); Eurol lists 21 L for the 818 | |
| Valve clearances | Check your handbook for the clearances. The dealer schedule lists a valve clearance check every 2,000 hours. | |
| Engine oil | 15W-40 engine oil (79038710B) | 17 L |
| Vario transmission | 821XL hydraulic/transmission fluid, grade: check your handbook (79035451B) | 43 L (712–716), 48 L (718, 818, 820) |
| Hydraulics | 821XL hydraulic/transmission fluid, grade: check your handbook (79037113B) | 46 L (Eurol: 50 L) |
| Rear axle final drives | 85W-140 gear oil | 11 L (712–716), 13 L (718, 818, 820) |
| Front axle differential | 80W-90 gear oil (79036959B) | 9 L (Eurol: 8.3 L) |
| Front axle hubs | 80W-90 gear oil (79036959B) | 3 L |
| Front PTO (if fitted) | 821XL hydraulic/transmission fluid (79037113B) | 4 L (Eurol: 3.5 L) |
| Clutch/brake actuation reservoir | Pentosin fluid (dealer part 72313538) | check your handbook |
| Coolant | Premixed Fleetguard antifreeze (CC2826) | 19 L (Eurol: 21 L) |
Specifications
| Front axle toe-in | 0 to 1 mm (0 to 0.04 in) |
| Wheel nut torques (dealer schedule) | Front centre to hub 330 ft/lb (450 Nm); front rim to dish 207 ft/lb (280 Nm); rear centre to hub 430 ft/lb (580 Nm); rear hub tapers to axle (3-step) 340 ft/lb (459 Nm); rear rim to dish 206 ft/lb (280 Nm); rear wheel weights (M16 bolts) 195 ft/lb |
Known problems
Which model you have
The dealer lists 712, 714, 716, 718, 818 and 820 on one schedule. The 718, 818 and 820 take more transmission and final drive oil than the 712, 714 and 716. The dealer list does not name the 815, 817 or 819: check your handbook for those.
Air brake antifreeze
The dealer lists an air brake antifreeze level check and a tank drain valve check at every service. Check your handbook for the fluid.
Oil quantities
The dealer gives quantities only. Always fill to the dipstick or filler hole level in your handbook.
Fault codes: Brakes, compressed air, diff lock and steering pump 05.x.xx
Comfort hydraulics, compressed air and brake monitoring
| Code | Meaning | What to do |
|---|---|---|
| 05.1.00 / 05.1.FF / 05.1.56 / 05.1.66 / 05.1.8D / 05.1.8F / 05.1.B0 / 05.1.FD / 05.1.FE | Control unit memory or parameter checksum error | Dealer EOL programming. |
| 05.1.FB / 05.1.FC | 12 V sensor supply fault / tractor type not compatible with software | Dealer. |
| 05.1.34 / 05.1.51-05.1.53 | Diff lock sensor, button or solenoid fault | Check the plug; dealer. |
| 05.1.54 / 05.1.55 / 05.1.58 / 05.1.59 | Brake switch or brake wear sensor fault | Have the brakes checked. |
| 05.1.5A / 05.1.5B | Left or right brake pad worn | Have the pads replaced now. |
| 05.1.60-05.1.62 | Compressed air sensor fault or readings disagree | Check air gauge and leaks; dealer. |
| 05.2.63 / 05.1.64 / 05.1.65 / 05.2.6A | Air pressure insufficient, leaking, too high, or compressor duty exceeded | Do not drive on the road with low brake air; dealer. |
| 05.1.70-05.1.72 | Front axle lubrication pressure sensor fault or pressure too low | Stop and have it checked; low axle lube pressure can damage the axle. |
| 05.1.91-05.1.96 | Power lift auto-mode or STOP button fault | Dealer. |
| 05.1.97-05.1.9E / 05.1.B1 / 05.1.B2 | Steering pump or emergency pump flow monitor fault, steering pump under 5 bar | Steering may be heavy: stop safely; dealer. |
| 05.1.E0 / 05.1.E8 / 05.1.EA / 05.2.E6 | Gateway relay, trailer brake monitoring failure or trailer brake disengaged | Check the trailer connection and brakes before moving. |
| 05.1.EB-05.1.ED | Steering brake locking clamp or brake pedal lock sensor fault | Dealer. |
| 05.1.F0-05.1.F3 | Steering brake servo valve faulty or active during 100% diff lock | Dealer. |
Fault codes: Instrument panel codes 00.x.xx (extra)
Instrument panel / CAN bus
| Code | Meaning | What to do |
|---|---|---|
| 00.0.0A | CAN bus fault to the electrical auxiliary spool valves | Check the fuse and plugs; dealer. |
| 00.0.0B / 00.0.17 | CAN bus fault to Variotronic TI | Restart; dealer if it returns. |
| 00.0.0E | CAN bus fault to VarioGuide | Guidance may be lost; restart, then dealer. |
| 00.0.0F | CAN bus fault to central electrics | Restart; dealer. |
| 00.0.10 | CAN bus fault to air conditioning (source says check the fuse) | Check the A/C fuse; same rating only. |
| 00.0.12 | CAN bus fault to tyre pressure monitoring (VarioGrip) | Check tyre pressures by gauge; dealer. |
| 00.0.14 | CAN bus fault to electrical auxiliary spool valves | Check fuse and plugs; dealer. |
| 00.0.19 / 00.0.1F | CAN bus fault (target not named in source) | Restart; dealer. |
| 00.0.1D | Engine ECU faults can't be shown on the panel (bus fault) | Dealer: you may not see engine warnings. |
| 00.0.21 | CAN bus fault to the on-board computer | Restart; dealer. |
| 00.1.4D-00.1.4F | CAN bus error inside the instrument panel | Restart; dealer. |
| 00.1.50 | Instrument panel not programmed | Dealer must programme the panel. |
| 00.1.71-00.1.78 | Enter, Esc, Up or Down key fault (inoperative, or held over 30 s) | Press and release each key cleanly; dealer if stuck. |
| 00.1.A0 | Fuel level too low | Refuel. |
| 00.1.AF | Air filter dirty (restriction sensor B215) | Clean or replace the air filter now. |
| 00.1.B1 | Battery voltage too low (alternator G002) | Check belt and battery terminals; get the charging checked. |
| 00.1.B2 | Battery voltage too high (alternator G002) | Dealer: risk of damage to electronics and battery. |
Fault codes: Central electrics and lights 0F.x.xx
Lights, wipers, washers, mirrors, central electrics
| Code | Meaning | What to do |
|---|---|---|
| 0F.1.01 / 0F.1.02 / 0F.1.17 / 0F.1.18 / 0F.1.32 | Brake or tail lamp (left, right, third) fault | Check the bulb and fuse. Needed for road use: fix before driving on the road. |
| 0F.1.03 / 0F.1.31 / 0F.1.13 | Marker, side marker or position light fault | Check bulb and fuse. |
| 0F.1.05-0F.1.08 | High beam, low beam, auxiliary high/low beam fault (the source lists the same note under .05 and .06) | Check bulb, fuse and relay; headlights are needed on the road. |
| 0F.1.09-0F.1.0C | Front or rear indicator fault | Check the bulb and fuse before road use. |
| 0F.2.0D / 0F.2.0E / 0F.2.0F / 0F.2.14 / 0F.2.1C | Rear socket indicator, stop-light or parking-light pin fault | Check the trailer plug and socket for damage. |
| 0F.1.10 / 0F.1.11 / 0F.1.12 / 0F.1.33 | Washer pump or nozzle heater fault | Check washer fluid and fuse. |
| 0F.1.15 / 0F.1.16 | Control panel or A/C control panel fault | Restart; dealer. |
| 0F.1.19 / 0F.1.1A / 0F.1.1B | Central electrics voltage too high/low or processor supply wrong | Check the battery and terminals; dealer. |
| 0F.1.1D / 0F.1.1E / 0F.1.34 | Wiper motor fault | Check wiper arms are free; fuse. |
| 0F.1.21 / 0F.1.27 / 0F.1.28 / 0F.1.2F | Stored values invalid or memory error | Dealer EOL programming. |
| 0F.1.2B / 0F.1.39 | Mirror heater or mirror adjustment fault | Fuse check. |
| 0F.1.2C / 0F.1.2D | Reversing drive solenoid fault | Dealer. |
| 0F.1.30 / 0F.1.35-0F.1.37 | Daytime running, work, interior or entry lighting fault | Check bulbs and fuses. |
Fault codes: Engine control unit codes 01.x.xx (extra)
Engine ECU (EDC), immobiliser, DPF and AdBlue
| Code | Meaning | What to do |
|---|---|---|
| 01.1.02 / 01.1.A1 | Engine ECU not sending speed message / not responding | Restart; dealer. |
| 01.1.04 / 01.1.07 | Checksum error in TMS or engine parameters | Dealer. |
| 01.1.0E | ABS unit detected on a tractor without ABS | Dealer. |
| 01.1.13-01.1.16 | Aftertreatment (DPF) CAN messages timed out or unexpected | Dealer. |
| 01.1.17 / 01.2.18 / 01.1.19 | Stationary DPF regeneration required or urgently required | Follow the handbook for a stationary regeneration in a safe open place; do it now if urgent. |
| 01.2.1B | Stationary regeneration in progress | Stay clear of the hot exhaust; don't leave it unattended. |
| 01.1.2E / 01.1.2F / 01.1.61-01.1.6C | Reversing fan or fan system fault (valve, speed, sensor, parameters) | Check the radiators are clean; watch temperature. |
| 01.1.34-01.1.3F | Immobiliser communication, serial-number or equipment mismatch | Try the other key; dealer. |
| 01.1.50-01.1.52 | Air filter sensor voltage out of range, or filter was dirty at last use | Inspect/clean the air filter. |
| 01.0.6D / 01.2.6F | AdBlue tank almost empty | Fill with AdBlue/DEF soon. |
| 01.1.6E / 01.1.F4 | AdBlue sensor or consumption message missing | Check DEF level; dealer. |
| 01.1.7A-01.1.7C / 01.1.9A-01.1.9C | Cruise MIN/MAX or TMS button defective or not communicating | Dealer. |
| 01.1.7E / 01.1.9E / 01.1.E0 | Hand throttle potentiometer defective, no comms or bad checksum | Check the plug; dealer. |
| 01.1.8A-01.1.8E | Engine temperature, charge-air temperature or fluid-level message timeouts | Dealer. |
| 01.1.8C | Starter lock vs clutch pedal check failed | Check the clutch pedal plug. |
| 01.1.A0 | Engine type mismatch or configuration message issue; torque reduced | Dealer. |
| 01.2.C0 | Seat empty with TMS enabled; TMS switched off | Sit in the seat. |
| 01.2.D0 / 01.1.D1 / 01.0.D2 / 01.1.D3 | Emissions-related fault: performance and then speed reduced if ignored | Don't ignore: check DEF level and call your dealer. |
| 01.1.F1 / 01.1.F2 | Immobiliser manipulation detected; performance limited (70% at F2) | Dealer. |
| 01.1.F3 | Fuel consumption message timeout | Dealer. |
Fault codes: Rear PTO and power lift 06, 08, 09 codes
PTO and front/rear linkage
| Code | Meaning | What to do |
|---|---|---|
| 06.1.01-06.1.03 / 06.1.11 / 06.1.41-06.1.43 / 06.1.A1 | PTO button, signal or bus fault, or button held over 30 s | Release buttons; the source says an emergency engage via the cab button (5 s) is possible. Dealer. |
| 06.1.04 | PTO clutch valve actuation fault | PTO disengages; dealer. |
| 06.1.05 / 06.1.10 / 06.1.13 | Clutch or stub shaft speed sensor fault, or shaft overspeed | Check fuse and plug; dealer. |
| 06.1.15-06.1.20 / 06.1.55-06.1.5A / 06.1.B5-06.1.BA | Speed preselection button fault or stuck (540/1000/1000E/1300, neutral) | Release buttons; dealer. |
| 06.1.1C / 06.1.1D | Valve actuation fault: PTO cannot engage | Dealer. |
| 06.1.45 / 06.1.50 / 06.1.60 | Clutch slip, shaft above 1300 rpm, or speed off setpoint by over 12% | Stop PTO work; dealer. |
| 06.1.E0-06.1.E8 | Control unit data checksum error | Dealer EOL programming. |
| 08.1.04-08.1.0B / 08.1.35 | Rear lift control unit parameter or configuration error | Dealer. |
| 08.2.1A / 08.1.1B / 08.1.1C | Rear lift not reaching height, lowering on its own, or imprecise | Lower the implement to the ground and stop; dealer. |
| 08.1.22 / 08.1.65 / 08.1.B0 | Rear position sensor fault, implausible or not calibrated | Dealer. |
| 08.1.38 / 08.1.39 / 08.2.1D | Rear lift pressure sensor fault | Dealer. |
| 08.1.40-08.1.4F | Rear lift button or switch fault | Check buttons; dealer. |
| 08.1.49 / 08.1.4A / 08.1.60-08.1.62 / 08.1.6B | Rear lift valve or solenoid faulty; valve moves to neutral | Dealer. |
| 09.1.1A-09.1.1C / 09.2.1A | Front lift sensor mismatch, lowering by itself, or imprecise | Lower the implement and stop; dealer. |
| 09.1.22 / 09.1.65 / 09.1.B0 / 09.1.68 | Front lift position sensor fault, implausible, not calibrated or upper limit exceeded | Dealer. |
| 09.1.60-09.1.63 / 09.1.6B | Front lift solenoid faulty (single acting only) | Dealer. |
| 09.1.E0-09.1.EF | Front lift valve electrical or spool fault; valve neutral and locked | Dealer; a jammed spool is often contamination. |
Fault codes: Varioterminal, armrest and basic control unit 02, 03, 1F
Terminal and armrest
| Code | Meaning | What to do |
|---|---|---|
| 02.0.02 / 02.0.80-02.0.82 | Terminal CAN, memory or checksum error | Restart; dealer EOL programming. |
| 02.1.41 / 02.1.44 / 02.2.40 / 02.2.43 | Terminal memory full or nearly full; VarioDoc disabled | Export and delete old tasks. |
| 02.1.83 / 02.2.48 | Terminal temperature out of range; brightness reduced | Let the cab warm or cool. |
| 02.1.90-02.1.92 / 02.1.98 | Keypad off: external controller silent, current monitor, button held, or internal fault | Release buttons; dealer. |
| 02.2.42 / 02.2.45 / 02.2.46 | Terminal and guidance receiver software incompatible or combination not allowed | Dealer software update. |
| 03.1.01-03.1.03 | Armrest memory, checksum or comms error | Dealer EOL programming. |
| 03.1.06-03.1.7F | Armrest parameters invalid (voltage, LIN, indicator, brightness, ramp, crossgate, modules, throttle, lifts) | Dealer EOL programming. |
| 03.1.0D-03.1.0F | Armrest circuit-board voltage fault | Check the battery; dealer. |
| 1F.1.B0 / 1F.1.B1 | Basic control unit communication fault | Dealer: clear fault memory then EOL programming. |
Fault codes: Transmission codes 04.x.xx (extra)
Vario transmission, hand brake and joystick
| Code | Meaning | What to do |
|---|---|---|
| 04.1.01 / 04.1.10-04.1.12 | 4WD clutch over-temperature, sensor or valve fault | Ease off 4WD use and let it cool; dealer. |
| 04.1.06 / 04.1.EC | Foot throttle sensor fault / not calibrated | Dealer recalibration. |
| 04.1.14-04.1.16, 04.1.1D-04.1.1F | Hydraulic motor 2 solenoid or speed sensor fault | Dealer. |
| 04.1.20 / 04.1.22 | Driving pedal potentiometer not calibrated or signal fault | Dealer. |
| 04.1.21 | Reverse drive switch fault | Check the switch. |
| 04.1.23-04.1.33 | Joystick or cruise-control switch / signal faults | Use pedal control; dealer. |
| 04.1.2A / 04.1.45 / 04.1.82 / 04.1.83 | Bevel pinion speed sensor (B015) fault or implausible | Dealer. |
| 04.1.3A | Gearbox range switch (S070) fault, calibration impossible | Dealer. |
| 04.1.3D / 04.1.3E | Power reduced because of an exhaust-related fault (or its data corrupt) | Check DEF/AdBlue and DPF warnings; dealer. |
| 04.1.49 / 04.1.50 / 04.1.56 | Transmission oil filter switch: signal fault or filter blocked | Replace the transmission oil filter if due; check the plug. |
| 04.2.52 / 04.1.53 | Gear oil temperature over 105 / 110 deg C | Ease the load and let it cool; clean coolers. |
| 04.1.58 | Transmission slip: output speed more than 30% off | Stop heavy work; dealer. |
| 04.1.5B / 04.2.5A | Radar sensor not calibrated / no pulse during calibration | Recalibrate per handbook, or dealer. |
| 04.1.69 / 04.1.72 / 04.1.73 / 04.1.78 / 04.2.A0 | Seat (driver presence) switch fault or seat state wrong | Sit properly in the seat; dealer if the switch faults. |
| 04.1.80 / 04.1.81 / 04.1.92-04.1.9E | Hand brake solenoids, sensor or lever fault, release/apply timeout | Don't rely on the parking brake: chock the wheels. Dealer. |
| 04.1.88 / 04.1.90 / 04.1.91 | Electric parking brake hardware or data fault | Chock the wheels; dealer. |
| 04.1.8F | Selected tyre circumference too small | Dealer to set the correct tyre size. |
| 04.1.9A | Double fault: no valid speed signal | Dealer. |
| 04.1.A1-04.1.A6 | Joystick/actuator unit turn-angle, track or reference-point fault | Dealer. |
| 04.1.BB / 04.1.D1 | Vehicle faster than the permitted speed | Slow down. |
| 04.1.C3-04.1.CA / 04.2.C0-04.2.C7 | Operator warnings: seat, pedal state, reversing mode, active standstill, hand brake, emergency operation, engine overspeed | Follow the on-screen prompt. |
| 04.2.CC-04.2.CE | Brake switches not set / cruise control blocked | Dealer if brake switches fault. |
| 04.2.D0 / 04.1.D5 | Workshop mode ratio restriction or comms error | Dealer. |
| 04.1.D3 / 04.2.D4 | Hand brake not applied with seat unoccupied | Apply the hand brake. |
| 04.1.E1-04.1.FA | Parameter checksum or calibration errors in the basic control unit | Dealer must reload parameters. |
| 04.1.EE / 04.1.EF | Gearbox characteristic or turbo-clutch valve not calibrated | Dealer calibration. |
Fault codes: Spool valves, air-con, front suspension and tyre pressure
0A, 10, 12 and 15 codes
| Code | Meaning | What to do |
|---|---|---|
| 0A.1.x0 / 0A.1.x1 / 0A.1.xE / 0A.1.xF | Spool valve x not reporting, memory fault, test fault or no target | Dealer. |
| 0A.1.x2 / 0A.1.x3 / 0A.1.x5 | Valve under- or over-voltage | Check the battery; dealer. |
| 0A.1.x4 / 0A.1.xA / 0A.1.xB | Spool stops short, deflects too far, or float not reached | Dealer. |
| 0A.1.x6 / 0A.1.x7 / 0A.1.xD | Pilot solenoid or position sensor fault, or pilot actuator jams | Dealer. |
| 0A.1.x8 / 0A.1.x9 / 0A.1.xC | Spool does not return to neutral, not neutral at start, or manual actuation | Stop; a valve stuck open can move an implement. Dealer. |
| 0A.1.D7-0A.1.DE | Hydraulic oil level sensor, low or empty tank, high temperature, clogged filter | Check the hydraulic oil level and filter; stop if empty. |
| 0A.1.F0-0A.1.FE | Control pressure solenoid, valve heating and external button faults | Dealer. |
| 10.1.31 / 10.1.32 | Air-flow flap actuator fault | Comfort only. |
| 10.1.34 / 10.1.3D | A/C compressor clutch or heater valve fault | Comfort only. |
| 10.1.35 / 10.1.3B / 10.1.40 | Blower fan fault | Check fuse. |
| 10.1.36-10.1.39 / 10.1.3F / 10.1.3C | A/C temperature or solar sensor fault (emergency mode) | Comfort only. |
| 10.1.3A | A/C checksum error | Dealer EOL programming. |
| 12.1.10-12.1.19 / 12.1.30-12.1.39 | VarioGrip front/rear axle: sensor, solenoid, leak, fill-rate or pressure fault; axle blocked | Check tyre pressures manually; dealer. |
| 12.1.52-12.1.55 | Tyre-pressure supply fault; axle(s) blocked | Dealer. |
| 12.2.04 / 12.2.05 / 12.2.13 / 12.2.33 / 12.2.50 | Tyre-pressure control aborted or waiting for the operator | Check the pressures are inside 0.5-2.6 bar; try again. |
| 12.1.00 / 12.1.B0 / 12.1.F0 / 12.1.F1 / 12.1.FE | Tyre-pressure system unknown, stored value, comms or memory error | Dealer EOL programming. |
| 15.1.62 / 15.1.63 / 15.1.66 / 15.1.69 / 15.1.6B | Front suspension raise, lower, preheat, stabiliser or lock solenoid fault | Suspension may lock; drive slowly. Dealer. |
| 15.1.64 / 15.1.65 | Suspension buttons on the armrest | Dealer. |
| 15.1.67 / 15.1.68 / 15.1.6C / 15.1.6D | Wheel position sensor fault, not calibrated or invalid values | Dealer calibration. |
Fault codes: Vario 700 / 800 / 900 fault codes
Vario terminal and controllers
| Code | Meaning | What to do |
|---|---|---|
| 00.0.01 | Bus fault: engine EDC is not getting its speed setting | Switch off and on. If the tractor will not rev or run correctly, call your dealer. |
| 00.0.02 | Terminal bus fault: terminal (A008) not reporting on the bus | Check battery and connectors; switch off and on. Call your dealer. |
| 0.0.12 | Terminal bus failure (A008): functions and display may be lost | Stop safely and call your dealer. |
| 00.0.03 | Multifunction armrest bus fault | Check armrest plugs. Call your dealer. |
| 00.0.04 / 0.0.14 | Transmission CAN bus fault: no setpoint to the actuator unit | Stop and call your dealer; drive may be lost. |
| 00.0.05 / 0.0.15 | 4WD / diff-lock bus fault | Call your dealer. |
| 00.0.06 / 0.0.16 | Rear PTO bus fault | Do not rely on the PTO; call your dealer. |
| 00.0.07 / 0.0.17 | Front PTO bus fault | Call your dealer. |
| 00.0.08 | Rear linkage (EPC) bus fault | Lower the linkage if safe; call your dealer. |
| 00.0.09 | Front linkage (EPC) bus fault | Call your dealer. |
| 00.0.15 | Front axle suspension bus fault | Call your dealer. |
| 00.0.18 | Electro-hydraulic steering (EHL) bus fault | Steering may be affected. Stop and call your dealer. |
| 00.0.1E | Engine EDC not reporting to the instrument panel | Check the dash for engine warnings; call your dealer. |
| 0.0.11 | EDC/EMR bus fault: fault in the engine ECU | Call your dealer. |
| 0.0.13 | Control console CAN bus failure (A004) | Call your dealer. |
| 00.1.55 | Hydraulic oil level sensor (B084) fault | Check the hydraulic oil level, then call your dealer if the code stays. |
| 00.1.59 | Fuel level sensor (B034) fault | Do not trust the fuel gauge; refuel by hours worked. |
| 00.1.54 | Compressed air pressure sensor fault (instrument cluster) | Check the air gauge; if pressure is low, stop and call your dealer. |
| 01.1.01 / 01.1.03 | Foot throttle pedal sensor (B055) fault | Check the pedal plug; use hand throttle only if safe and call your dealer. |
| 01.1.05 | Engine configuration cannot be read from EDC | Call your dealer. |
| 01.1.30 | No ignition key taught in (immobiliser) | Try your other key; call your dealer if it will not start. |
| 01.1.31 / 01.1.32 | Immobiliser fault; key without transponder | Use the original key; call your dealer. |
| 01.1.7D | Foot throttle idle switch fault | Check the pedal; call your dealer. |
| 01.1.7E | Hand throttle potentiometer electrical fault | Call your dealer. |
| 02.1.EE | ISO job computer (ISOBUS) error on the basic control unit | Check the implement connection and plug; call your dealer. |
| 03.1.01 / 03.1.02 / 03.1.03 | Armrest MFA internal hardware or software fault | Switch off and on; call your dealer. |
| 04.1.04 | Clutch pedal rotary sensor (B017) fault | Check the pedal; call your dealer. |
| 04.1.05 | High-pressure sensor II (B039) in the transmission: signal fault | Call your dealer. |
| 04.1.07 | High-pressure sensor 1 (B008) in the transmission: fault | Call your dealer. |
| 04.1.24 | Hand brake switch signal fault | Check the hand brake is fully released; call your dealer if the code stays. |
| 04.1.28 | Forward/reverse incremental encoder (A009) signal fault | Call your dealer. |
| 0F.1.23 | Basic control unit gets no data from the transmission | Stop and call your dealer. |
| 0F.1.26 | No data from the steering (EHL steering angle) | Steering may behave oddly; stop and call your dealer. |
| 0F.1.2B | Mirror heater fault | Check the mirror heater fuse. |
| 0F.2.0D / 0F.2.0E | Left / right indicator at the trailer socket faulty | Check the trailer plug and bulbs before road use. |
Repair guides
- Poor starting, power loss or water in the diesel: fuel pre-filter and filter change (Moderate, 45 minutes to 1½ hours): Engine hard to start or cuts out, loss of power, a water-in-fuel warning, or fuel filters that are due. Water ruins common-rail injectors, so do not carry on running with a water warning.
- Air system: water in the tanks, slow pressure build-up, air dryer cartridge (Moderate, 30–60 minutes): Water running out of the air tank drain, the compressor running very often, slow air build-up for trailer brakes, or a compressed air leak warning.
- Wheel nuts and front axle toe-in: checking after a tyre or axle job (Moderate, 1–2 hours): Front tyres wearing on the inside or outside edge, steering that wanders, loose or clicking wheels, or a tyre or axle job just completed.
- Belt squeal, overheating or a weeping water pump: belts, tensioner, pump and fan bearings (Moderate, 1–2 hours): A squealing or flapping belt, a charging or air-con fault, engine running hot, coolant weeping from the water pump weep hole, or a rumble from the fan area.
The full step-by-step guides are in Farmyard Workshop once you add your tractor.
Parts list with genuine part numbers
Maker part numbers per site service schedule: 700 and 800 Vario COM3 (712, 714, 716, 718, 818, 820) (c. 2007–2010 (Eurol, for the 818 Vario COM3); check your serial number); check serial range; plus Fendt 818 Vario parts book (718/00101-99999), AGCO Parts (COM3 family, shares most numbers with the 7xx books)
Engine service
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Engine oil | 79038710B | 1 | 15W-40. Engine oil, 17 L (Eurol lists 16.5 L for the 818 COM3) |
| Engine oil filter | F716200510020 | 1 | The seal supplied in the box should be white |
| Sump drain plug gasket | X540005678000 | 1 | |
| Primary (outer) air filter | H515200090100 | 1 | |
| Secondary (inner) air filter | H716200090110 | 1 | |
| Valve cover gasket | F712201210020 | 1 |
Fuel
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel filter | F731200060020 | 1 | |
| Fuel pre-filter | F842201060010 | 1 |
Cooling
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Coolant | CC2826 | 1 | Premixed Fleetguard antifreeze, 19 L |
| Coolant drain plug gasket | X540002478000 | 1 |
Transmission and hydraulics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Transmission oil | 79035451B | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook). 43 L on 712, 714 and 716, and 48 L on 718, 818 and 820 (dealer notes; the dealer's pack quantity is 48 L) |
| Pressure filter | F91610060001A | 1 | |
| Pressure filter O-ring | 72313495 | 1 | |
| Suction filter | F916100490010 | 1 | |
| Suction filter O-ring | 72424095 | 1 | |
| Drain plug gasket | X540008278000 | 2 | Dealer lists 2 |
| Drain plug gasket (second size) | X540010278000 | 1 | |
| Hydraulic oil | 79037113B | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook), 46 L (Eurol lists 50 L for the 818 COM3) |
| Hydraulic return filter | G716860060310 | 1 | O-ring is 72312305 |
| Hydraulic vent filter | X820001191000 | 1 | |
| Drain plug O-ring | X548842900000 | 1 | |
| Dipstick O-ring | 568-114 | 1 | |
| End plate service part | F716961020220 | 1 | Dealer job: service end plate / test accumulator. O-rings 72433580 and 72433582 |
| End plate service part (second) | F716961020330 | 1 |
Front axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Front axle differential oil | 79036959B | 1 | 80W-90. Gear oil, 9 L (dealer quantity; Eurol lists 8.3 L) |
| Differential seal (dealer lists with the oil) | 742508 | 2 | Dealer lists 2 |
| Differential drain plug gasket | X540007678000 | 2 | |
| Hub gasket | X540009678000 | 2 | |
| Front PTO oil | 79037113B | 1 | 821XL hydraulic/transmission fluid (grade: check your handbook), 4 L |
| Front PTO filter | 716150200160 | 1 | O-ring is 72376561 |
| Front PTO gasket | X540008278000 | 2 | Dealer lists 2 |
| Front PTO gasket (second part) | X548926666000 | 1 |
Rear axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Drain plug gasket | X540009478000 | 4 | Dealer lists 4 |
Cab
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fresh air filter | H816810140071 | 2 | Dealer lists 2 |
| Recirculating air filter | 920810140040 | 2 | Dealer lists 2 |
| Heater air filter | H716810130011 | 1 |
Other
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Grease | 79014728B | 1 | Lithium grease for the front axle driveline; dealer grease pack 79014728B. Grade for the other points: check your handbook |
Disc brake [04-0008]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Brake disc, inner | 835100321071 | Wear part | |
| Brake disc, outer | 716150150500 | Wear part | |
| Brake plate | 716151150060 | ||
| Brake piston | 524101150131 | ||
| Feed plunger | 524101150140 | ||
| Operating disc | G718150150030 | ||
| Ball | F822100150020 | ||
| Pulling spring | F524101150010 | ||
| Compression spring | X699305400000 | ||
| Lunette ring | X531500400000 | ||
| Shaft seal 70x95x11/13/02 | X550139301000 | Seal | |
| O-ring 11x3 | X548829266000 | Seal | |
| Plain compression ring 70x3x2.45 | X560713601000 | Seal | |
| Shaft | 718150150040 | ||
| Nozzle M10x8 | 716150150160 | ||
| Nozzle | 718150150060 |
Brake master cylinder [04-0011]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Brake master cylinder | G822100070030 | ||
| Repair kit, master cylinder | F822100070070 | Service part | |
| Dual tank (reservoir) | G822100070071 | ||
| Reservoir cover | F822100070080 | ||
| Reservoir screen sleeve | F291100070060 | ||
| Balance line | 822100070500 | ||
| Brake fluid Pentosin CHF 11S 1L | X902011622000 |
Handbrake [04-0017]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Handbrake lever | H716150030011 | ||
| Handbrake lever housing | 716150030140 | ||
| Ratchet rod | 716150030010 | ||
| Pawl | 238104030090 | ||
| Tooth sector | 716150030180 | ||
| Handle grip | 716150030160 | ||
| Bellows | 716150030150 | ||
| Bearing bushing | X605013000000 | Wear part | |
| Compression spring | 250100030060 | ||
| Seal | 716150030040 | Seal |
Hydraulic clutch [04-0023]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Clutch master cylinder | G524100100051 | ||
| Clutch master cylinder repair kit | F524100100010 | Service part | |
| Brake hose | H411150070100 | ||
| Bleeder valve | G514100100060 | ||
| Elbow fitting | F821100070500 | ||
| Pressure hose (cut to length) | X604173000980 |
Clutch disc [04-0027]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Hydro damper | 716100420113 | ||
| Drive shaft | 718100420012 | ||
| Drive shaft seal | 716100420160 | Seal | |
| O-ring 30x5 | X548887266000 | Seal | |
| Profile ring | 716100420171 | Seal |
PTO clutch [04-0044]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Inner disc | 716150220660 | Wear part | |
| Fin disc | 934152220480 | Wear part | |
| Support plate | 916100320140 | ||
| Piston | 718150220250 | ||
| Piston | 411151220070 | ||
| O-ring 42x2.5 | X548911400000 | Seal | |
| Disc spring | 716150220360 | ||
| Shaft lip seal 40x51x2.5 | 514100220430 | Seal | |
| Shaft lip seal PTO 112x125x2.5 | 822100220380 | Seal | |
| Ball bearing 6208 | X606111111000 | ||
| Ball bearing 6205 | X605510602000 | ||
| PTO clutch drive shaft | H716151220051 |
Transmission pressure filter [04-0057]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Transmission high pressure filter assembly | G916100600061 | Service part | |
| Hydraulic filter cartridge | F916100600011 | Service part | |
| Hydraulic filter cartridge (valve block) | 395100600020 | Service part | |
| Filter O-ring 76x2.5 | X548960666000 | Seal | |
| Filter housing | F916100600030 |
Oil cooler [04-0059]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Oil cooler, oil to air | H718100510121 | ||
| Oil cooler, oil to air | H718100510131 |
Engine filters [01]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel filter assembly | F716201060010 | ||
| Fuel filter cartridge | F716201060070 | Service part | |
| Fuel filter seal | F716201060080 | Seal | |
| Fuel pre-filter assembly | G916200060100 | ||
| Fuel pre-filter cartridge 30 micron | F916200060010 | Service part | |
| Fuel pre-filter cartridge 10 micron | F916200060100 | Service part | |
| Fuel pre-filter seal | F916200060020 | Seal | |
| Fuel pre-filter seal | F916200060081 | Seal | |
| Fuel pre-filter glass bowl | F916200060050 | ||
| Fuel pre-filter glass bowl seal | F916200060062 | Seal | |
| Fuel pre-filter drain valve | F916200060030 | ||
| Air filter assembly, dry dual element | G718202090010 | ||
| Engine air filter cartridge (inner) | H716200090100 | Service part | |
| Dust discharge valve | 716200090100 |
Engine service parts [01]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Seal kit without cylinder head | F716201210720 | ||
| Head gasket 1.10mm | F718202210170 | ||
| Head gasket 1.20mm | F718202210140 | ||
| Head gasket 1.30mm | F718202210160 | ||
| Thermostat without housing | F119200050040 | Service part | |
| Thermostat seal 60x3.5 | F716201050030 | Seal | |
| Water pump | F731200610020 | ||
| Serpentine belt PK8 | F404200040020 | Wear part | |
| V-belt (air conditioning) | X696624100000 | Wear part |
Alternator and starter [07]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Alternator | F718901010010 | ||
| Alternator regulator | F515900010010 | ||
| Alternator carbon brush | F515900010020 | Wear part | |
| Starter motor | F716903060010 | ||
| Starter solenoid | F716900060050 | ||
| Starter pinion | F716900060070 |
Front axle [02]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Wheel hub | F718301020370 | ||
| Hub shaft seal | H524300020100 | Seal | |
| Hub tapered roller bearing | F718301020680 | Wear part | |
| Hub taper roller bearing | X619069900005 | Wear part | |
| Hub taper roller bearing | X619069800005 | Wear part | |
| Hub O-ring 253.59x3.53 | X549040200000 | Seal | |
| Ring gear | F718301020390 | ||
| Planetary gear | F718301020340 |
Steering [02]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Steering cylinder | E718301121010 | ||
| Steering cylinder seal kit | G001990011330 | Service part | |
| Steering cylinder guide bush | F716300120010 | ||
| Steering cylinder O-ring 24x5 | X548872200000 | Seal | |
| Steering cylinder O-ring 64x3 | X548945466000 | Seal | |
| Steering cylinder scraper | X540410601000 | Seal | |
| Steering cylinder bearing seal 40x48x8 | X548317500000 | Seal | |
| Steering cylinder rod | F411301120020 | ||
| Tie rod and ball joint assembly | G716300100010 | Track rod end | |
| Tie rod and ball joint assembly | G716300100050 | Track rod end | |
| Tie rod ball joint | F716300100040 | Wear part | |
| Tie rod dust boot | F514300100030 | ||
| Tie rod sealing cup | F385300100080 |
Hydraulic system [06]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Piston pump | G716940010011 | ||
| Pump seal kit | F514940010010 | Service part | |
| Pump bearing kit | F412940010050 | ||
| Pump control valve | F514940010020 | ||
| Pump distributor plate | F514940010040 | ||
| Pump molded seal | 816940010010 | Seal | |
| Directional control valve | G916961022013 | ||
| Directional valve seal kit | F716961020020 | Service part | |
| Valve parts kit | F816960020060 | ||
| Valve O-ring | F816860100020 | Seal | |
| Valve O-ring | F916961022100 | Seal |
Rear linkage [13]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Top link control arm | G716870050021 | ||
| Top link turnbuckle tube | F411872050010 | ||
| Top link jointed spindle | F716870050030 | ||
| Top link hook | G199870050101 | ||
| Top link hook opening lever | F199870050010 | ||
| Top link hook operating cable | G184870050090 | ||
| Ball sleeve cat 3/2 | 0066288100000 | Wear part | |
| Ball sleeve cat 3 | 0066290100000 | Wear part | |
| Bottom link control arm, left | H716870060013 | ||
| Bottom link control arm, right | H716870060023 | ||
| Lower link arm | 718870060151 | ||
| Bottom link parts kit | F816870060030 | ||
| Bottom link ball sleeve cat 3/2 | 281870062040 | Wear part | |
| Linkage ball cat 3 | 281870062050 | Wear part | |
| Quick coupler, long | 0066053200000 |
Cab [08]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Wiper motor | G716810170021 | ||
| Wiper arm | G816810170020 | ||
| Wiper blade | H716810170010 | Wear part | |
| Wiper arm seal | 205812170041 | Seal |
Sources
- AGCO/Fendt part numbers, intervals, quantities, valve clearances and torques: the Fendt dealer's COM3 maintenance schedule (Maple Lane Farm Service, Ontario). Each hour tab (?hours=1000, 1500 ...) was compared to find which job belongs to which interval
- Engine (Deutz TCD 2012 L06 4V), years, capacities and a 12-month oil limit for the 818 Vario COM3
- AGCO Parts parts book
More from Fendt.