Fendt 800 Vario SCR service schedule
Fendt 800 Vario · c. 2010–2014 (SCR, Stage 3B; check your serial number)
Covers the Fendt 800 Vario SCR (822, 824, 826, 828; Fendt codes 833–836).
Every maker's service job for the Fendt 800 Vario SCR, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.
Track your 800 Vario SCR for freeVersions: 822, 824, 826, 828 Vario SCR
Service intervals
| Job | When |
|---|---|
| Engine oil and filter change | every 500 hours |
| Fuel pre-filter (water separator) change | every 500 hours |
| AdBlue (DEF) filter change | every 500 hours |
| Cab fresh air and recirculation filters | every 500 hours |
| Lubricate all grease points | every 500 hours |
| Main fuel filter change | every 1,000 hours |
| Engine air filter, primary (outer) element | every 1,000 hours |
| Engine air filter, secondary (inner) element | every 1,000 hours |
| Engine belts, idler and tensioner check | every 1,000 hours |
| Transmission pressure filter change | every 1,000 hours |
| Front axle differential and hub oil change | every 1,000 hours |
| Hydraulic oil and filters change | every 1,000 hours |
| Compressed air dryer cartridge change | every 1,000 hours |
| Engine coolant change | every 2,000 hours |
| Engine valve clearance check | every 2,000 hours |
| Vario transmission oil and filters change | every 2,000 hours |
| Front PTO oil and filter change (if fitted) | every 2,000 hours |
| AdBlue tank breather filter | every 2,000 hours |
Service jobs and parts
Engine oil and filter change
Engine · every 500 hours
The Fendt dealer's schedule changes the engine oil, oil filter and drain plug gasket at every 500-hour service. There is no DPF on the SCR-only tractors, so no regeneration is needed first.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Engine oil | 1 | 10W-40 Deutz engine oil (dealer pack 79036470B), 18 L. Check your handbook for the exact Deutz oil specification. Aztec Oils match: EMPROTEC XHPD 10W-40 | check your handbook |
| Engine oil filter | 1 | F836200510080 | |
| Oil drain plug gasket | 1 | M18x24 | F731200510060 |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Let it stand a few minutes. Hot oil burns, and the exhaust is very hot after a regeneration. Wear gloves.
- Remove the sump drain plug and let the oil drain fully.
- Remove the old oil filter, check the old seal came off with it, and wipe the filter head clean.
- Oil the new filter seal and fit the filter as its instructions say.
- Fit a new gasket to the drain plug, refit it, and fill with 10W-40 Deutz engine oil to the full mark on the dipstick.
- Run the engine for a minute, check for leaks, stop it and recheck the level.
Tools: Drain tray (25 L), Filter wrench, Spanner for sump plug, Funnel, Rags, Gloves
Fuel pre-filter (water separator) change
Fuel · every 500 hours
The dealer schedule lists the fuel pre-filter at every 500-hour service, and says to drain water from it as required. Water in the diesel ruins common-rail injectors.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fuel pre-filter | 1 | F842201060010 |
Step-by-step
- Stop the engine, take the key out and chock the wheels. Keep naked flames away.
- Clean around the pre-filter so dirt cannot get in.
- Drain any water into a container, then remove the old filter.
- Fit the new filter with a clean, oiled seal, hand-tight.
- Prime the system as your handbook describes. Never crack open the high-pressure pipes on a common-rail engine.
- Start the engine and check for leaks.
Tools: Container for fuel, Filter wrench, Rags, Gloves
AdBlue (DEF) filter change
Exhaust · every 500 hours
The dealer schedule lists the DEF filter at every 500-hour service. Blocked AdBlue filters cause dosing faults and engine power cuts.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| AdBlue (DEF) filter | 1 | Supersedes 02934690 (dealer parts page) | ACP0594170 |
Step-by-step
- Stop the engine and take the key out. Wait for the AdBlue system to finish purging after shutdown before opening anything.
- Clean around the filter cap so dirt and crystals cannot get in.
- Remove the cap and old filter, catching any AdBlue in a container.
- Fit the new filter and refit the cap as your handbook says.
- Rinse spilt AdBlue off with water; it corrodes metal and electrical connectors.
Tools: Container, Gloves, Eye protection, Clean water
Cab fresh air and recirculation filters
Cab · every 500 hours
The dealer schedule changes both cab filters at every 500-hour service. Clogged filters weaken the air conditioning and let dust into the cab.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fresh air filter | 1 | H931812140600 | |
| Recirculating air filter | 1 | H931812140511 |
Step-by-step
- Stop the engine and take the key out.
- Open the cab filter covers as your handbook shows.
- Take out the old filters, wipe out the housings and fit the new ones.
- Refit the covers. Clean the A/C condenser at the same time.
Tools: Screwdriver or Torx driver (check your handbook)
Lubricate all grease points
Chassis · every 500 hours
The dealer schedule lists 'lubricate all grease points' at every service tab, from 500 hours up. It does not list the points. Check your handbook for the grease points and for shorter intervals for the busy ones.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Grease | 1 | Dealer pack 79014728B; check your handbook for the right grease | 79014728B |
Step-by-step
- Wipe each nipple clean before greasing.
- Grease every point your handbook shows, such as the front axle, steering, linkage and PTO shaft, until fresh grease shows.
- Wipe off the surplus so it does not collect dirt.
- Check for loose hardware, linkages and leaks while you are under there.
Tools: Grease gun, Rags
Main fuel filter change
Fuel · every 1,000 hours
The dealer schedule changes the main fuel filter at the 1,000-hour service and every 1,000 hours after that.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fuel filter | 1 | F731200060020 |
Step-by-step
- Stop the engine, take the key out and chock the wheels. Keep naked flames away.
- Clean around the filter housing before opening anything.
- Remove the old filter into a container and check the old seal came off.
- Fit the new filter with a new seal or O-ring.
- Prime the system as your handbook describes. Never crack open the high-pressure pipes.
- Start the engine and check for leaks.
Tools: Container for fuel, Filter wrench, Rags, Gloves
Engine air filter, primary (outer) element
Engine · every 1,000 hours
The dealer schedule replaces the primary air filter at the 1,000-hour service. At 1,500 and 2,500 hours it only checks and cleans the filters (dealer lists 72608874 outer and 72437627 inner for those checks).
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Primary (outer) air filter | 1 | F842201090010 |
Step-by-step
- Stop the engine and take the key out. Never run the engine with a filter out.
- Open the air cleaner housing and take out the element, taking care not to let dirt fall into the intake.
- Wipe the housing out with a damp cloth. Do not blow dirt down the intake.
- Fit the new element, check it seats evenly and close the housing.
- Check the intake hoses and clips for leaks and clear the filter warning on the terminal if needed.
Tools: Torch, Damp cloth
Engine air filter, secondary (inner) element
Engine · every 1,000 hours
The dealer schedule replaces the secondary (safety) air filter at the 1,000-hour service on the SCR tractors, together with the primary.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Secondary (inner) air filter | 1 | H931202090400 |
Step-by-step
- Stop the engine and take the key out. Never run the engine with a filter out.
- Open the air cleaner housing and take out the element, taking care not to let dirt fall into the intake.
- Wipe the housing out with a damp cloth. Do not blow dirt down the intake.
- Fit the new element, check it seats evenly and close the housing.
- Check the intake hoses and clips for leaks and clear the filter warning on the terminal if needed.
Tools: Torch, Damp cloth
Engine belts, idler and tensioner check
Engine · every 1,000 hours
The dealer schedule says to take the belts off and check the idler and tensioner bearings and the belts at the 1,000-hour service, and to check belt condition at the visits in between.
Step-by-step
- Stop the engine and take the key out.
- Release the tensioner and take the belts off.
- Spin the idler and tensioner by hand: they should run smoothly and quietly.
- Look for cracks, fraying and glazing on the belts and replace them if worn.
- Refit the belts, check the routing and tension, and check the water pump and fan bearings for play and leaks at the weep hole.
Tools: Spanner for tensioner, Torch
Transmission pressure filter change
Transmission · every 1,000 hours
The dealer schedule changes the transmission pressure filter and its O-ring at the 1,000-hour service, in between the oil changes. Clean oil is what keeps the Vario transmission alive.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission pressure filter | 1 | O-ring 72313495 | F83510060003A |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Clean around the filter housing, put a tray underneath and remove the old filter.
- Fit the new filter with a new O-ring.
- Run the engine, check the transmission oil level and for leaks.
Tools: Filter wrench, Drain tray, Rags, Gloves
Front axle differential and hub oil change
Front axle · every 1,000 hours
The dealer schedule changes the front axle differential oil and the hub oil at the 1,000-hour service and every 1,000 hours after that. The differential takes 80W-90 gear oil with LS (limited slip) additive.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Front axle differential oil | 1 | 80W-90 gear oil (dealer pack 79036959B), 9 L. Aztec Oils match: TRANSMATEC EP-4 80W-90 | 79036959B |
| Front differential gaskets | 2 | X540007678000 | |
| Gasket (dealer lists with the differential) | 2 | Dealer part 742508; check your handbook for what it fits | 742508 |
| Front axle hub oil | 1 | 80W-90 gear oil (79036959B), 4 L. Aztec Oils match: TRANSMATEC EP-4 80W-90 | 79036959B |
| Front hub drain plug gaskets | 2 | X540009678000 |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Warm the axle by driving a short way, then park level and take the key out.
- Put a tray under the differential and remove the filler plug, then the drain plug. Let it drain fully.
- Fit a new gasket and refit the drain plug. Fill the differential with 80W-90 gear oil to the filler plug level.
- Do the same on each front hub, one at a time, with new gaskets.
- Check for leaks and wipe up spills; oil on the tyres makes them slippery. Check the front axle toe-in at the same time: the schedule gives 0 to 2 mm.
Tools: Drain trays, Socket set, Torque wrench, Oil pump or syringe, Gloves
Hydraulic oil and filters change
Hydraulics · every 1,000 hours
The dealer schedule changes the hydraulic oil, the O-ring and the return, vent and control pressure filters at every 1,000-hour service on the SCR tractors.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Hydraulic oil | 1 | 821XL hydraulic/transmission fluid (dealer pack 79037113B), 102 L. Check your handbook for the European oil. Aztec Oils match: AGRITEC UTTO | 79037113B |
| Drain plug O-ring | 1 | M15.4 x 2.1 | X548842900000 |
| Hydraulic return line filter | 1 | G835860061040 | |
| Hydraulic vent filter | 1 | F835860061020 | |
| Control pressure fine filter | 1 | O-ring 72454666 | F931962025010 |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Warm the oil by running the hydraulics for a few minutes, then stop and take the key out. Hot oil burns, so wear gloves.
- Put a large tray under the drain plug, remove the plug and let the oil drain fully.
- Change the return line filter, the vent filter and the control pressure fine filter, with their O-rings.
- Clean the external pressure supply sieve filter as your handbook shows.
- Refit the drain plug with a new O-ring, refill with the right oil to the mark, run the hydraulics and recheck the level.
- Drain the oil recovery bottles at the couplers as required.
Tools: Drain tray (large), Filter wrench, Socket set, Funnel or pump, Gloves
Compressed air dryer cartridge change
Brakes · every 1,000 hours
The dealer schedule changes the air dryer cartridge at the 1,000-hour service. A tired dryer lets water into the air system.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Air dryer cartridge | 1 | Dealer note: without TPMS 1 filter, with TPMS 2 filters; check your handbook | F842880141020 |
Step-by-step
- Stop the engine, let the air pressure down as your handbook says and chock the wheels.
- Unscrew the old cartridge and wipe the seat clean.
- Fit the new cartridge with a lightly oiled seal.
- Run the compressor, check for leaks and operate the tank drain valve to drain any water.
Tools: Filter wrench or strap, Rags
Engine coolant change
Cooling · every 2,000 hours
The dealer schedule changes the engine coolant and the drain plug gasket at the 2,000-hour service.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Coolant | 1 | Premixed Fleetguard coolant (dealer part CC2826), 30 L | CC2826 |
| Coolant drain plug gasket | 1 | X540002478000 |
Step-by-step
- Work only on a cold engine. Never open the cap hot: coolant can spray out and scald you.
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Drain the cooling system into a clean tray and fit a new drain plug gasket.
- Refill with premixed coolant to the level in your handbook, run the engine to temperature and top up.
- Check for leaks. Coolant is poisonous to animals: catch it all and dispose of it properly.
Tools: Drain tray (40 L), Funnel, Antifreeze tester, Gloves
Engine valve clearance check
Engine · every 2,000 hours
The dealer schedule lists a valve clearance check at the 2,000-hour service. The clearances are not on the schedule: check your handbook.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Valve cover gasket | 1 | Dealer note: valve cover gasket, reusable. The dealer also lists ACO 725200010251 with it without describing it; check your handbook | 72649554 |
Step-by-step
- Only check with the engine cold. Take the key out.
- Follow the Fendt service manual to remove the cover and set each cylinder as it describes.
- Check the clearances against your handbook figures, adjust if needed, then recheck.
- If you do not have the service manual and tools, have your Fendt dealer do it.
Tools: Feeler gauges, Torque wrench, Service manual
Vario transmission oil and filters change
Transmission · every 2,000 hours
The dealer schedule changes the transmission oil, suction filter and drain plug gaskets every 2,000 hours, and the pressure filter every 1,000 hours (see the previous task). The page lists 123 L for the transmission and 102 L for the hydraulics, which look like a combined system on this tractor; check your handbook for how the circuits are filled.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission oil | 1 | 821XL hydraulic/transmission fluid (dealer pack 79035451B), 123 L. Check your handbook for the European oil. Aztec Oils match: AGRITEC UTTO | 79035451B |
| Drain plug gaskets | 1 | X540010278000 | |
| Drain plug assembly | 1 | Dealer note: only if required | 72427121 |
| Transmission pressure filter | 1 | Also changed with the oil; O-ring 72313495 | F83510060003A |
| Transmission suction filter | 1 | O-ring 72424095 | F835100490050 |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Warm the transmission by driving a short way, then park level and take the key out. Hot oil burns, so wear gloves.
- Put a large tray under the transmission and remove the drain plugs.
- Change the suction filter and the pressure filter with new O-rings, as your handbook shows.
- Refit the drain plugs with new gaskets and refill with the right oil.
- Run the engine and check the oil level and for leaks. Do a rolling stop test afterwards to check there is no brake drag.
Tools: Drain tray (large), Filter wrench, Socket set, Funnel or pump, Gloves
Front PTO oil and filter change (if fitted)
Front PTO · every 2,000 hours
The dealer schedule changes the front PTO oil, its filter and gaskets at 2,000 hours, if the tractor has a front PTO.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Front PTO oil | 1 | 821XL hydraulic/transmission fluid (dealer pack 79037113B), 4 L. Check your handbook for the European oil. Aztec Oils match: AGRITEC UTTO | 79037113B |
| Front PTO filter | 1 | O-ring 72376561 | 716150200160 |
| Front PTO gaskets | 2 | X540008278000 |
Step-by-step
- Park on level ground, lower the linkage, loader and any implement to the ground, stop the engine, take the key out and chock the wheels.
- Put a tray under the front PTO housing and remove the drain plug with its gasket.
- Change the filter and its O-ring.
- Fit new gaskets, refit the plug and refill with the right oil to the level mark.
- Run the PTO briefly with nothing connected, stop and recheck the level.
Tools: Drain tray, Socket set, Filter wrench, Gloves
AdBlue tank breather filter
Exhaust · every 2,000 hours
The dealer schedule changes the DEF breather filter and blows out its hose every 2,000 hours.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| AdBlue breather filter | 1 | H835200730200 |
Step-by-step
- Stop the engine and take the key out.
- Remove the old breather filter and blow the breather hose clear with compressed air.
- Fit the new breather filter.
Tools: Compressed air, Gloves
Oils, fluids and capacities
| System | Oil or spec | Capacity |
|---|---|---|
| Engine | Deutz TCD 2012 L06 4V 6.06 L six-cylinder turbo diesel with SCR (AdBlue), no particulate filter | |
| Engine oil | 10W-40 synthetic Deutz engine oil (dealer pack 79036470B). Check your handbook for the exact Deutz specification. | 18 L (dealer schedule) |
| Coolant | Premixed Fleetguard coolant (dealer part CC2826), 30 L | |
| Valve clearances | Check your handbook for the clearances. The dealer schedule lists a valve clearance check every 2,000 hours. | |
| Engine oil | 10W-40 synthetic Deutz engine oil (79036470B) | 18 L |
| Vario transmission | 821XL hydraulic/transmission fluid (79035451B). Check your handbook for the European oil | 123 L (dealer) |
| Hydraulics | 821XL hydraulic/transmission fluid (79037113B). Check your handbook for the European oil | 102 L (dealer) |
| Front axle differential | 80W-90 gear oil with LS additive (79036959B) | 9 L |
| Front axle hubs | 80W-90 gear oil (79036959B) | 4 L |
| Front PTO (if fitted) | 821XL hydraulic/transmission fluid (79037113B) | 4 L |
| Clutch and brake actuation fluid | Pentosin fluid (dealer part 72313538) | Check the level; capacity not given |
| Coolant | Premixed Fleetguard coolant (CC2826) | 30 L |
Specifications
| Engine | Deutz 6.06 L six-cylinder (TCD 2012 L06 4V) |
| Transmission | Fendt Vario stepless |
| Front axle toe-in | 0–2 mm (0 to 0.08 in) |
| Wheel nut torques (dealer schedule) | Front centre to hub 450 Nm (330 ft/lb); front rim to dish 280 Nm (207 ft/lb); rear centre to hub 580 Nm (430 ft/lb); rear hub tapers to axle 600 Nm (442 ft/lb) (3-step tightening); rear rim to dish 280 Nm (206 ft/lb); rear wheel weights (M16 bolts) 195 ft/lb with M16 bolts |
Known problems
Hydraulic oil every 1,000 hours on the SCR tractors
The dealer schedule lists the hydraulic oil and its filters at every 1,000-hour tab but the transmission oil only at 2,000 hours. Check your handbook before relying on either.
Capacity wording
The dealer page lists 123 L for the transmission and 102 L for the hydraulics. Fill to the level marks rather than by quantity.
Fault codes: Brakes, compressed air, diff lock and steering pump 05.x.xx
Comfort hydraulics, compressed air and brake monitoring
| Code | Meaning | What to do |
|---|---|---|
| 05.1.00 / 05.1.FF / 05.1.56 / 05.1.66 / 05.1.8D / 05.1.8F / 05.1.B0 / 05.1.FD / 05.1.FE | Control unit memory or parameter checksum error | Dealer EOL programming. |
| 05.1.FB / 05.1.FC | 12 V sensor supply fault / tractor type not compatible with software | Dealer. |
| 05.1.34 / 05.1.51-05.1.53 | Diff lock sensor, button or solenoid fault | Check the plug; dealer. |
| 05.1.54 / 05.1.55 / 05.1.58 / 05.1.59 | Brake switch or brake wear sensor fault | Have the brakes checked. |
| 05.1.5A / 05.1.5B | Left or right brake pad worn | Have the pads replaced now. |
| 05.1.60-05.1.62 | Compressed air sensor fault or readings disagree | Check air gauge and leaks; dealer. |
| 05.2.63 / 05.1.64 / 05.1.65 / 05.2.6A | Air pressure insufficient, leaking, too high, or compressor duty exceeded | Do not drive on the road with low brake air; dealer. |
| 05.1.70-05.1.72 | Front axle lubrication pressure sensor fault or pressure too low | Stop and have it checked; low axle lube pressure can damage the axle. |
| 05.1.91-05.1.96 | Power lift auto-mode or STOP button fault | Dealer. |
| 05.1.97-05.1.9E / 05.1.B1 / 05.1.B2 | Steering pump or emergency pump flow monitor fault, steering pump under 5 bar | Steering may be heavy: stop safely; dealer. |
| 05.1.E0 / 05.1.E8 / 05.1.EA / 05.2.E6 | Gateway relay, trailer brake monitoring failure or trailer brake disengaged | Check the trailer connection and brakes before moving. |
| 05.1.EB-05.1.ED | Steering brake locking clamp or brake pedal lock sensor fault | Dealer. |
| 05.1.F0-05.1.F3 | Steering brake servo valve faulty or active during 100% diff lock | Dealer. |
Fault codes: Instrument panel codes 00.x.xx (extra)
Instrument panel / CAN bus
| Code | Meaning | What to do |
|---|---|---|
| 00.0.0A | CAN bus fault to the electrical auxiliary spool valves | Check the fuse and plugs; dealer. |
| 00.0.0B / 00.0.17 | CAN bus fault to Variotronic TI | Restart; dealer if it returns. |
| 00.0.0E | CAN bus fault to VarioGuide | Guidance may be lost; restart, then dealer. |
| 00.0.0F | CAN bus fault to central electrics | Restart; dealer. |
| 00.0.10 | CAN bus fault to air conditioning (source says check the fuse) | Check the A/C fuse; same rating only. |
| 00.0.12 | CAN bus fault to tyre pressure monitoring (VarioGrip) | Check tyre pressures by gauge; dealer. |
| 00.0.14 | CAN bus fault to electrical auxiliary spool valves | Check fuse and plugs; dealer. |
| 00.0.19 / 00.0.1F | CAN bus fault (target not named in source) | Restart; dealer. |
| 00.0.1D | Engine ECU faults can't be shown on the panel (bus fault) | Dealer: you may not see engine warnings. |
| 00.0.21 | CAN bus fault to the on-board computer | Restart; dealer. |
| 00.1.4D-00.1.4F | CAN bus error inside the instrument panel | Restart; dealer. |
| 00.1.50 | Instrument panel not programmed | Dealer must programme the panel. |
| 00.1.71-00.1.78 | Enter, Esc, Up or Down key fault (inoperative, or held over 30 s) | Press and release each key cleanly; dealer if stuck. |
| 00.1.A0 | Fuel level too low | Refuel. |
| 00.1.AF | Air filter dirty (restriction sensor B215) | Clean or replace the air filter now. |
| 00.1.B1 | Battery voltage too low (alternator G002) | Check belt and battery terminals; get the charging checked. |
| 00.1.B2 | Battery voltage too high (alternator G002) | Dealer: risk of damage to electronics and battery. |
Fault codes: Central electrics and lights 0F.x.xx
Lights, wipers, washers, mirrors, central electrics
| Code | Meaning | What to do |
|---|---|---|
| 0F.1.01 / 0F.1.02 / 0F.1.17 / 0F.1.18 / 0F.1.32 | Brake or tail lamp (left, right, third) fault | Check the bulb and fuse. Needed for road use: fix before driving on the road. |
| 0F.1.03 / 0F.1.31 / 0F.1.13 | Marker, side marker or position light fault | Check bulb and fuse. |
| 0F.1.05-0F.1.08 | High beam, low beam, auxiliary high/low beam fault (the source lists the same note under .05 and .06) | Check bulb, fuse and relay; headlights are needed on the road. |
| 0F.1.09-0F.1.0C | Front or rear indicator fault | Check the bulb and fuse before road use. |
| 0F.2.0D / 0F.2.0E / 0F.2.0F / 0F.2.14 / 0F.2.1C | Rear socket indicator, stop-light or parking-light pin fault | Check the trailer plug and socket for damage. |
| 0F.1.10 / 0F.1.11 / 0F.1.12 / 0F.1.33 | Washer pump or nozzle heater fault | Check washer fluid and fuse. |
| 0F.1.15 / 0F.1.16 | Control panel or A/C control panel fault | Restart; dealer. |
| 0F.1.19 / 0F.1.1A / 0F.1.1B | Central electrics voltage too high/low or processor supply wrong | Check the battery and terminals; dealer. |
| 0F.1.1D / 0F.1.1E / 0F.1.34 | Wiper motor fault | Check wiper arms are free; fuse. |
| 0F.1.21 / 0F.1.27 / 0F.1.28 / 0F.1.2F | Stored values invalid or memory error | Dealer EOL programming. |
| 0F.1.2B / 0F.1.39 | Mirror heater or mirror adjustment fault | Fuse check. |
| 0F.1.2C / 0F.1.2D | Reversing drive solenoid fault | Dealer. |
| 0F.1.30 / 0F.1.35-0F.1.37 | Daytime running, work, interior or entry lighting fault | Check bulbs and fuses. |
Fault codes: Engine control unit codes 01.x.xx (extra)
Engine ECU (EDC), immobiliser, DPF and AdBlue
| Code | Meaning | What to do |
|---|---|---|
| 01.1.02 / 01.1.A1 | Engine ECU not sending speed message / not responding | Restart; dealer. |
| 01.1.04 / 01.1.07 | Checksum error in TMS or engine parameters | Dealer. |
| 01.1.0E | ABS unit detected on a tractor without ABS | Dealer. |
| 01.1.13-01.1.16 | Aftertreatment (DPF) CAN messages timed out or unexpected | Dealer. |
| 01.1.17 / 01.2.18 / 01.1.19 | Stationary DPF regeneration required or urgently required | Follow the handbook for a stationary regeneration in a safe open place; do it now if urgent. |
| 01.2.1B | Stationary regeneration in progress | Stay clear of the hot exhaust; don't leave it unattended. |
| 01.1.2E / 01.1.2F / 01.1.61-01.1.6C | Reversing fan or fan system fault (valve, speed, sensor, parameters) | Check the radiators are clean; watch temperature. |
| 01.1.34-01.1.3F | Immobiliser communication, serial-number or equipment mismatch | Try the other key; dealer. |
| 01.1.50-01.1.52 | Air filter sensor voltage out of range, or filter was dirty at last use | Inspect/clean the air filter. |
| 01.0.6D / 01.2.6F | AdBlue tank almost empty | Fill with AdBlue/DEF soon. |
| 01.1.6E / 01.1.F4 | AdBlue sensor or consumption message missing | Check DEF level; dealer. |
| 01.1.7A-01.1.7C / 01.1.9A-01.1.9C | Cruise MIN/MAX or TMS button defective or not communicating | Dealer. |
| 01.1.7E / 01.1.9E / 01.1.E0 | Hand throttle potentiometer defective, no comms or bad checksum | Check the plug; dealer. |
| 01.1.8A-01.1.8E | Engine temperature, charge-air temperature or fluid-level message timeouts | Dealer. |
| 01.1.8C | Starter lock vs clutch pedal check failed | Check the clutch pedal plug. |
| 01.1.A0 | Engine type mismatch or configuration message issue; torque reduced | Dealer. |
| 01.2.C0 | Seat empty with TMS enabled; TMS switched off | Sit in the seat. |
| 01.2.D0 / 01.1.D1 / 01.0.D2 / 01.1.D3 | Emissions-related fault: performance and then speed reduced if ignored | Don't ignore: check DEF level and call your dealer. |
| 01.1.F1 / 01.1.F2 | Immobiliser manipulation detected; performance limited (70% at F2) | Dealer. |
| 01.1.F3 | Fuel consumption message timeout | Dealer. |
Fault codes: Rear PTO and power lift 06, 08, 09 codes
PTO and front/rear linkage
| Code | Meaning | What to do |
|---|---|---|
| 06.1.01-06.1.03 / 06.1.11 / 06.1.41-06.1.43 / 06.1.A1 | PTO button, signal or bus fault, or button held over 30 s | Release buttons; the source says an emergency engage via the cab button (5 s) is possible. Dealer. |
| 06.1.04 | PTO clutch valve actuation fault | PTO disengages; dealer. |
| 06.1.05 / 06.1.10 / 06.1.13 | Clutch or stub shaft speed sensor fault, or shaft overspeed | Check fuse and plug; dealer. |
| 06.1.15-06.1.20 / 06.1.55-06.1.5A / 06.1.B5-06.1.BA | Speed preselection button fault or stuck (540/1000/1000E/1300, neutral) | Release buttons; dealer. |
| 06.1.1C / 06.1.1D | Valve actuation fault: PTO cannot engage | Dealer. |
| 06.1.45 / 06.1.50 / 06.1.60 | Clutch slip, shaft above 1300 rpm, or speed off setpoint by over 12% | Stop PTO work; dealer. |
| 06.1.E0-06.1.E8 | Control unit data checksum error | Dealer EOL programming. |
| 08.1.04-08.1.0B / 08.1.35 | Rear lift control unit parameter or configuration error | Dealer. |
| 08.2.1A / 08.1.1B / 08.1.1C | Rear lift not reaching height, lowering on its own, or imprecise | Lower the implement to the ground and stop; dealer. |
| 08.1.22 / 08.1.65 / 08.1.B0 | Rear position sensor fault, implausible or not calibrated | Dealer. |
| 08.1.38 / 08.1.39 / 08.2.1D | Rear lift pressure sensor fault | Dealer. |
| 08.1.40-08.1.4F | Rear lift button or switch fault | Check buttons; dealer. |
| 08.1.49 / 08.1.4A / 08.1.60-08.1.62 / 08.1.6B | Rear lift valve or solenoid faulty; valve moves to neutral | Dealer. |
| 09.1.1A-09.1.1C / 09.2.1A | Front lift sensor mismatch, lowering by itself, or imprecise | Lower the implement and stop; dealer. |
| 09.1.22 / 09.1.65 / 09.1.B0 / 09.1.68 | Front lift position sensor fault, implausible, not calibrated or upper limit exceeded | Dealer. |
| 09.1.60-09.1.63 / 09.1.6B | Front lift solenoid faulty (single acting only) | Dealer. |
| 09.1.E0-09.1.EF | Front lift valve electrical or spool fault; valve neutral and locked | Dealer; a jammed spool is often contamination. |
Fault codes: Varioterminal, armrest and basic control unit 02, 03, 1F
Terminal and armrest
| Code | Meaning | What to do |
|---|---|---|
| 02.0.02 / 02.0.80-02.0.82 | Terminal CAN, memory or checksum error | Restart; dealer EOL programming. |
| 02.1.41 / 02.1.44 / 02.2.40 / 02.2.43 | Terminal memory full or nearly full; VarioDoc disabled | Export and delete old tasks. |
| 02.1.83 / 02.2.48 | Terminal temperature out of range; brightness reduced | Let the cab warm or cool. |
| 02.1.90-02.1.92 / 02.1.98 | Keypad off: external controller silent, current monitor, button held, or internal fault | Release buttons; dealer. |
| 02.2.42 / 02.2.45 / 02.2.46 | Terminal and guidance receiver software incompatible or combination not allowed | Dealer software update. |
| 03.1.01-03.1.03 | Armrest memory, checksum or comms error | Dealer EOL programming. |
| 03.1.06-03.1.7F | Armrest parameters invalid (voltage, LIN, indicator, brightness, ramp, crossgate, modules, throttle, lifts) | Dealer EOL programming. |
| 03.1.0D-03.1.0F | Armrest circuit-board voltage fault | Check the battery; dealer. |
| 1F.1.B0 / 1F.1.B1 | Basic control unit communication fault | Dealer: clear fault memory then EOL programming. |
Fault codes: Transmission codes 04.x.xx (extra)
Vario transmission, hand brake and joystick
| Code | Meaning | What to do |
|---|---|---|
| 04.1.01 / 04.1.10-04.1.12 | 4WD clutch over-temperature, sensor or valve fault | Ease off 4WD use and let it cool; dealer. |
| 04.1.06 / 04.1.EC | Foot throttle sensor fault / not calibrated | Dealer recalibration. |
| 04.1.14-04.1.16, 04.1.1D-04.1.1F | Hydraulic motor 2 solenoid or speed sensor fault | Dealer. |
| 04.1.20 / 04.1.22 | Driving pedal potentiometer not calibrated or signal fault | Dealer. |
| 04.1.21 | Reverse drive switch fault | Check the switch. |
| 04.1.23-04.1.33 | Joystick or cruise-control switch / signal faults | Use pedal control; dealer. |
| 04.1.2A / 04.1.45 / 04.1.82 / 04.1.83 | Bevel pinion speed sensor (B015) fault or implausible | Dealer. |
| 04.1.3A | Gearbox range switch (S070) fault, calibration impossible | Dealer. |
| 04.1.3D / 04.1.3E | Power reduced because of an exhaust-related fault (or its data corrupt) | Check DEF/AdBlue and DPF warnings; dealer. |
| 04.1.49 / 04.1.50 / 04.1.56 | Transmission oil filter switch: signal fault or filter blocked | Replace the transmission oil filter if due; check the plug. |
| 04.2.52 / 04.1.53 | Gear oil temperature over 105 / 110 deg C | Ease the load and let it cool; clean coolers. |
| 04.1.58 | Transmission slip: output speed more than 30% off | Stop heavy work; dealer. |
| 04.1.5B / 04.2.5A | Radar sensor not calibrated / no pulse during calibration | Recalibrate per handbook, or dealer. |
| 04.1.69 / 04.1.72 / 04.1.73 / 04.1.78 / 04.2.A0 | Seat (driver presence) switch fault or seat state wrong | Sit properly in the seat; dealer if the switch faults. |
| 04.1.80 / 04.1.81 / 04.1.92-04.1.9E | Hand brake solenoids, sensor or lever fault, release/apply timeout | Don't rely on the parking brake: chock the wheels. Dealer. |
| 04.1.88 / 04.1.90 / 04.1.91 | Electric parking brake hardware or data fault | Chock the wheels; dealer. |
| 04.1.8F | Selected tyre circumference too small | Dealer to set the correct tyre size. |
| 04.1.9A | Double fault: no valid speed signal | Dealer. |
| 04.1.A1-04.1.A6 | Joystick/actuator unit turn-angle, track or reference-point fault | Dealer. |
| 04.1.BB / 04.1.D1 | Vehicle faster than the permitted speed | Slow down. |
| 04.1.C3-04.1.CA / 04.2.C0-04.2.C7 | Operator warnings: seat, pedal state, reversing mode, active standstill, hand brake, emergency operation, engine overspeed | Follow the on-screen prompt. |
| 04.2.CC-04.2.CE | Brake switches not set / cruise control blocked | Dealer if brake switches fault. |
| 04.2.D0 / 04.1.D5 | Workshop mode ratio restriction or comms error | Dealer. |
| 04.1.D3 / 04.2.D4 | Hand brake not applied with seat unoccupied | Apply the hand brake. |
| 04.1.E1-04.1.FA | Parameter checksum or calibration errors in the basic control unit | Dealer must reload parameters. |
| 04.1.EE / 04.1.EF | Gearbox characteristic or turbo-clutch valve not calibrated | Dealer calibration. |
Fault codes: Spool valves, air-con, front suspension and tyre pressure
0A, 10, 12 and 15 codes
| Code | Meaning | What to do |
|---|---|---|
| 0A.1.x0 / 0A.1.x1 / 0A.1.xE / 0A.1.xF | Spool valve x not reporting, memory fault, test fault or no target | Dealer. |
| 0A.1.x2 / 0A.1.x3 / 0A.1.x5 | Valve under- or over-voltage | Check the battery; dealer. |
| 0A.1.x4 / 0A.1.xA / 0A.1.xB | Spool stops short, deflects too far, or float not reached | Dealer. |
| 0A.1.x6 / 0A.1.x7 / 0A.1.xD | Pilot solenoid or position sensor fault, or pilot actuator jams | Dealer. |
| 0A.1.x8 / 0A.1.x9 / 0A.1.xC | Spool does not return to neutral, not neutral at start, or manual actuation | Stop; a valve stuck open can move an implement. Dealer. |
| 0A.1.D7-0A.1.DE | Hydraulic oil level sensor, low or empty tank, high temperature, clogged filter | Check the hydraulic oil level and filter; stop if empty. |
| 0A.1.F0-0A.1.FE | Control pressure solenoid, valve heating and external button faults | Dealer. |
| 10.1.31 / 10.1.32 | Air-flow flap actuator fault | Comfort only. |
| 10.1.34 / 10.1.3D | A/C compressor clutch or heater valve fault | Comfort only. |
| 10.1.35 / 10.1.3B / 10.1.40 | Blower fan fault | Check fuse. |
| 10.1.36-10.1.39 / 10.1.3F / 10.1.3C | A/C temperature or solar sensor fault (emergency mode) | Comfort only. |
| 10.1.3A | A/C checksum error | Dealer EOL programming. |
| 12.1.10-12.1.19 / 12.1.30-12.1.39 | VarioGrip front/rear axle: sensor, solenoid, leak, fill-rate or pressure fault; axle blocked | Check tyre pressures manually; dealer. |
| 12.1.52-12.1.55 | Tyre-pressure supply fault; axle(s) blocked | Dealer. |
| 12.2.04 / 12.2.05 / 12.2.13 / 12.2.33 / 12.2.50 | Tyre-pressure control aborted or waiting for the operator | Check the pressures are inside 0.5-2.6 bar; try again. |
| 12.1.00 / 12.1.B0 / 12.1.F0 / 12.1.F1 / 12.1.FE | Tyre-pressure system unknown, stored value, comms or memory error | Dealer EOL programming. |
| 15.1.62 / 15.1.63 / 15.1.66 / 15.1.69 / 15.1.6B | Front suspension raise, lower, preheat, stabiliser or lock solenoid fault | Suspension may lock; drive slowly. Dealer. |
| 15.1.64 / 15.1.65 | Suspension buttons on the armrest | Dealer. |
| 15.1.67 / 15.1.68 / 15.1.6C / 15.1.6D | Wheel position sensor fault, not calibrated or invalid values | Dealer calibration. |
Fault codes: Vario 700 / 800 / 900 fault codes
Vario terminal and controllers
| Code | Meaning | What to do |
|---|---|---|
| 00.0.01 | Bus fault: engine EDC is not getting its speed setting | Switch off and on. If the tractor will not rev or run correctly, call your dealer. |
| 00.0.02 | Terminal bus fault: terminal (A008) not reporting on the bus | Check battery and connectors; switch off and on. Call your dealer. |
| 0.0.12 | Terminal bus failure (A008): functions and display may be lost | Stop safely and call your dealer. |
| 00.0.03 | Multifunction armrest bus fault | Check armrest plugs. Call your dealer. |
| 00.0.04 / 0.0.14 | Transmission CAN bus fault: no setpoint to the actuator unit | Stop and call your dealer; drive may be lost. |
| 00.0.05 / 0.0.15 | 4WD / diff-lock bus fault | Call your dealer. |
| 00.0.06 / 0.0.16 | Rear PTO bus fault | Do not rely on the PTO; call your dealer. |
| 00.0.07 / 0.0.17 | Front PTO bus fault | Call your dealer. |
| 00.0.08 | Rear linkage (EPC) bus fault | Lower the linkage if safe; call your dealer. |
| 00.0.09 | Front linkage (EPC) bus fault | Call your dealer. |
| 00.0.15 | Front axle suspension bus fault | Call your dealer. |
| 00.0.18 | Electro-hydraulic steering (EHL) bus fault | Steering may be affected. Stop and call your dealer. |
| 00.0.1E | Engine EDC not reporting to the instrument panel | Check the dash for engine warnings; call your dealer. |
| 0.0.11 | EDC/EMR bus fault: fault in the engine ECU | Call your dealer. |
| 0.0.13 | Control console CAN bus failure (A004) | Call your dealer. |
| 00.1.55 | Hydraulic oil level sensor (B084) fault | Check the hydraulic oil level, then call your dealer if the code stays. |
| 00.1.59 | Fuel level sensor (B034) fault | Do not trust the fuel gauge; refuel by hours worked. |
| 00.1.54 | Compressed air pressure sensor fault (instrument cluster) | Check the air gauge; if pressure is low, stop and call your dealer. |
| 01.1.01 / 01.1.03 | Foot throttle pedal sensor (B055) fault | Check the pedal plug; use hand throttle only if safe and call your dealer. |
| 01.1.05 | Engine configuration cannot be read from EDC | Call your dealer. |
| 01.1.30 | No ignition key taught in (immobiliser) | Try your other key; call your dealer if it will not start. |
| 01.1.31 / 01.1.32 | Immobiliser fault; key without transponder | Use the original key; call your dealer. |
| 01.1.7D | Foot throttle idle switch fault | Check the pedal; call your dealer. |
| 01.1.7E | Hand throttle potentiometer electrical fault | Call your dealer. |
| 02.1.EE | ISO job computer (ISOBUS) error on the basic control unit | Check the implement connection and plug; call your dealer. |
| 03.1.01 / 03.1.02 / 03.1.03 | Armrest MFA internal hardware or software fault | Switch off and on; call your dealer. |
| 04.1.04 | Clutch pedal rotary sensor (B017) fault | Check the pedal; call your dealer. |
| 04.1.05 | High-pressure sensor II (B039) in the transmission: signal fault | Call your dealer. |
| 04.1.07 | High-pressure sensor 1 (B008) in the transmission: fault | Call your dealer. |
| 04.1.24 | Hand brake switch signal fault | Check the hand brake is fully released; call your dealer if the code stays. |
| 04.1.28 | Forward/reverse incremental encoder (A009) signal fault | Call your dealer. |
| 0F.1.23 | Basic control unit gets no data from the transmission | Stop and call your dealer. |
| 0F.1.26 | No data from the steering (EHL steering angle) | Steering may behave oddly; stop and call your dealer. |
| 0F.1.2B | Mirror heater fault | Check the mirror heater fuse. |
| 0F.2.0D / 0F.2.0E | Left / right indicator at the trailer socket faulty | Check the trailer plug and bulbs before road use. |
Repair guides
- AdBlue (SCR) warnings: DEF filter, breather filter and sensor pre-filter (Specialist, 1–2 hours for the filter changes; dosing, sensor and heater faults need a dealer): AdBlue dosing or quality warnings, reduced engine power linked to the SCR system, an AdBlue filter that is due, or an AdBlue tank that will not vent properly.
- Poor starting, power loss or water in the diesel: fuel pre-filter and filter change (Moderate, 45 minutes to 1½ hours): Engine hard to start or cuts out, loss of power, a water-in-fuel warning, or fuel filters that are due. Water ruins common-rail injectors, so do not carry on running with a water warning.
- Air system: water in the tanks, slow pressure build-up, air dryer cartridge (Moderate, 30–60 minutes): Water running out of the air tank drain, the compressor running very often, slow air build-up for trailer brakes, or a compressed air leak warning.
- Wheel nuts and front axle toe-in: checking after a tyre or axle job (Moderate, 1–2 hours): Front tyres wearing on the inside or outside edge, steering that wanders, loose or clicking wheels, or a tyre or axle job just completed.
- Belt squeal, overheating or a weeping water pump: belts, tensioner, pump and fan bearings (Moderate, 1–2 hours): A squealing or flapping belt, a charging or air-con fault, engine running hot, coolant weeping from the water pump weep hole, or a rumble from the fan area.
- Transmission pressure filter change and the rolling stop test for brake drag (Specialist, 1–2 hours for the filter; the road test follows): Transmission pressure warnings, sluggish creeping or hot brakes after transmission work, or a service that includes the transmission pressure filter.
- Weak cab ventilation or air-con: fresh air filter, recirculation filters and condenser (Easy, 30–45 minutes): Weak air flow from the vents, dusty cab, misting windscreen, air-conditioning not cooling, or a squealing A/C compressor belt.
The full step-by-step guides are in Farmyard Workshop once you add your tractor.
Parts list with genuine part numbers
Maker part numbers per site service schedule: 800 Vario SCR (822, 824, 826, 828; Fendt codes 833–836) (c. 2010–2014 (SCR, Stage 3B; check your serial number)); check serial range; plus Fendt 822 Vario SCR parts book (833/00101-99999), AGCO Parts
Engine service
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Engine oil filter | F836200510080 | 1 | |
| Oil drain plug gasket | F731200510060 | 1 | M18x24 |
| Primary (outer) air filter | F842201090010 | 1 | |
| Secondary (inner) air filter | H931202090400 | 1 | |
| Valve cover gasket | 72649554 | 1 | Dealer note: valve cover gasket, reusable. The dealer also lists ACO 725200010251 with it without describing it; check your handbook |
Fuel
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel pre-filter | F842201060010 | 1 | |
| Fuel filter | F731200060020 | 1 |
Exhaust and AdBlue
| Part | Part number | Qty | Notes |
|---|---|---|---|
| AdBlue (DEF) filter | ACP0594170 | 1 | Supersedes 02934690 (dealer parts page) |
| AdBlue breather filter | H835200730200 | 1 |
Cooling
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Coolant | CC2826 | 1 | Premixed Fleetguard coolant (dealer part CC2826), 30 L |
| Coolant drain plug gasket | X540002478000 | 1 |
Transmission and hydraulics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Transmission pressure filter | F83510060003A | 1 | O-ring 72313495 |
| Transmission oil | 79035451B | 1 | 821XL hydraulic/transmission fluid (dealer pack 79035451B), 123 L. Check your handbook for the European oil |
| Drain plug gaskets | X540010278000 | 1 | |
| Drain plug assembly | 72427121 | 1 | Dealer note: only if required |
| Transmission suction filter | F835100490050 | 1 | O-ring 72424095 |
| Hydraulic oil | 79037113B | 1 | 821XL hydraulic/transmission fluid (dealer pack 79037113B), 102 L. Check your handbook for the European oil |
| Drain plug O-ring | X548842900000 | 1 | M15.4 x 2.1 |
| Hydraulic return line filter | G835860061040 | 1 | |
| Hydraulic vent filter | F835860061020 | 1 | |
| Control pressure fine filter | F931962025010 | 1 | O-ring 72454666 |
Brakes
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Air dryer cartridge | F842880141020 | 1 | Dealer note: without TPMS 1 filter, with TPMS 2 filters; check your handbook |
Front axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Front axle differential oil | 79036959B | 1 | 80W-90 gear oil (dealer pack 79036959B), 9 L |
| Front differential gaskets | X540007678000 | 2 | |
| Gasket (dealer lists with the differential) | 742508 | 2 | Dealer part 742508; check your handbook for what it fits |
| Front hub drain plug gaskets | X540009678000 | 2 |
PTO
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Front PTO oil | 79037113B | 1 | 821XL hydraulic/transmission fluid (dealer pack 79037113B), 4 L. Check your handbook for the European oil |
| Front PTO filter | 716150200160 | 1 | O-ring 72376561 |
| Front PTO gaskets | X540008278000 | 2 |
Cab
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fresh air filter | H931812140600 | 1 | |
| Recirculating air filter | H931812140511 | 1 |
Other
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Grease | 79014728B | 1 | Dealer pack 79014728B; check your handbook for the right grease |
Filters guide [01-0001]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Engine oil filter cartridge | F836200510010 | Service part | |
| DEF (AdBlue) filter | F835201110090 | Service part | |
| Gear oil pressure filter cartridge | F835100600031 | Service part | |
| Breather, external pressure connection | F931962020390 | Service part | |
| Compressed air filter element | F931882140010 | Service part |
Disc brake [05-0011]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Brake caliper | G835150150050 | ||
| Brake piston | G835150150080 | Wear part | |
| Brake piston repair kit | U835150410000 | Service part | |
| Inner brake disc | 835150150230 | Wear part | |
| Shim disc | 835150150120 | ||
| Compression spring 2x11x32 | X699313700000 |
Brake pedals [05-0013]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Brake pedal | H835150070022 | ||
| Pedal bearing | H835150070012 | Wear part | |
| Bearing bushing | X609535100000 | Wear part | |
| Pressure plate | 835150070030 | ||
| Pulling spring 2.2x15x74.2 | X699415700000 | ||
| Pulling spring 3.2x19.2x62 | X699420200000 | ||
| Buffer | 178109100050 |
Brake valve [05-0015]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Brake valve | G835151071100 |
Handbrake [05-0033]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Handbrake valve | G835150030121 | ||
| Handbrake valve parts kit | F835150030010 | Service part | |
| Throttle jet 0.5 | 842810290010 |
Hydraulic clutch [05-0038]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Clutch/brake fluid dual tank | G822100070071 | ||
| Tank cover | F822100070080 | ||
| Tank screen sleeve | F291100070060 | ||
| Brake fluid Pentosin CHF 11S 1L | X902011622000 | ||
| Clutch hose | H835100700030 | ||
| Clutch boost pipe | H835100700060 | ||
| Bleeder valve | G514100100060 |
Transmission pressure filter [05-0063]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Gear oil pressure filter assembly | G835100600043 | ||
| Hydraulic filter cartridge | F835100600031 | Service part | |
| Filter O-ring 76x2.5 | X548960666000 | Seal | |
| Filter housing | F835100600020 | ||
| O-ring 18.72x2.62 | X548857366000 | Seal |
Engine service parts [02]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Oil cooler housing | F836200510030 | ||
| Engine oil filter housing cover | F411201510070 | ||
| Oil cooler seal | F716201510120 | Seal | |
| Oil cooler seal | F934201510100 | Seal | |
| Oil drain valve | F718202510030 | ||
| Fuel filter joint | F731200060030 | Seal | |
| Fuel pre-filter assembly | G339202060102 | ||
| Fuel pre-filter assembly with heating | G339202060110 | ||
| Fuel pre-filter, spin-on with water sensor | F339202060250 | Service part | |
| Fuel pre-filter seal kit | F339202060290 | Service part | |
| Fuel pre-filter O-ring | F339202060320 | Seal | |
| Air filter assembly, dry dual element | G835200090010 | ||
| Air filter cover | F835200090010 | ||
| Seal kit without cylinder head | F836200210470 | ||
| Seal kit without cylinder head | F743200210040 | ||
| Cylinder head gasket 1.30mm | F836200210420 | ||
| Cylinder head gasket 1.40mm | F836200210430 | ||
| Head gasket 1.50mm | F842201210060 | ||
| Water pump without pulley | F416200610010 | ||
| Water pump V-belt sheave | F836200610160 | ||
| Thermostat housing (engine up to 11020362) | F836200610020 | Check engine number | |
| Thermostat housing (engine from 11020363) | F836200610190 | Check engine number | |
| Thermostat without housing | F340200610020 | Service part | |
| Thermostat housing seal | F836200610170 | Seal | |
| Serpentine belt PK8 | F836200040020 | Wear part |
Front axle [03]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Wheel hub | F835300020320 | ||
| Hub shaft seal 195x18 | H926301020100 | Seal | |
| Hub O-ring 253.59x3.53 | X549040200000 | Seal | |
| Hub taper roller bearing JP13049A | X619070000003 | Wear part | |
| Hub tapered roller bearing | F835300020820 | Wear part | |
| Hub tapered roller bearing | F835300020830 | Wear part | |
| Ring gear | F835300020330 | ||
| Ring gear carrier | F835300020340 | ||
| Planetary carrier | F835300020370 |
Steering [03/04]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Steering cylinder | F835300020480 | ||
| Steering cylinder seal kit | F835300020520 | Service part | |
| Steering cylinder rod | F835300020510 | ||
| Tie rod and ball joint assembly | F835300020490 | Track rod end | |
| Tie rod | F835300020530 | Track rod | |
| Tie rod ball joint | F926301100010 | Wear part | |
| Tie rod dust boot | F926301100030 | ||
| Tie rod sealing cup | F816300100070 | ||
| Steering unit | G835400090070 | ||
| Steering unit seal kit | F916400090010 | Service part |
Alternator and starter [08]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Alternator | F404900010040 | ||
| Alternator V-belt sheave | F404900010010 | ||
| Alternator field governor 14.4V | F718901010140 | ||
| Starter motor | F836900060060 | ||
| Starter solenoid | F836900060050 | ||
| Starter relay | F836900060040 |
Rear linkage [13]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Bottom link control arm | H931920071022 | ||
| Lower link arm, hook end | H931920071032 | ||
| Lower link | 718921070170 | ||
| Bottom link parts kit | F816870060030 | ||
| Bottom link hook | 013821010190 | Wear part | |
| Lift system wire | H718922070040 | ||
| Ball sleeve 64x45 | 281870062040 | Wear part | |
| Top link, hook end | G930920050010 | ||
| Top link jointed spindle | F716870050030 | ||
| Top link turnbuckle tube | F395870050030 | ||
| Top link hook | G199870050101 | Wear part | |
| Top link hook opening lever | F199870050010 | ||
| Top link spring | 270870050300 | ||
| Top link catch | 931920050282 | ||
| Top link ball sleeve cat 3/2 | 0066288100000 | Wear part |
Cab [09]
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Wiper motor | G931812170020 | ||
| Wiper arm | H931812170070 | ||
| Wiper blade 500mm | H737812180020 | Wear part | |
| Mirror head, electric control | G931812150021 | ||
| Mirror bracket | G931812150010 | ||
| Mirror replacement glass | F931812150010 | ||
| Mirror telescopic tube | F931812150030 | ||
| Mirror parts kit | F816810150200 |
Sources
- Fendt 800 SCR schedule: 1,000 to 3,000 hour tabs, all intervals, AGCO part numbers, quantities and torques (Maple Lane Farm Service, Fendt dealer). Hour tabs on the schedule page (?hours=500, 1000 ... 3000) were compared to find which job belongs to which interval
- AdBlue filter ACP0594170 supersedes 02934690 (same dealer's parts page)
- Deutz TCD 2012 L06 engine, 6,056 cm³, Stage 3B with SCR, 2010–2014 (Traktorenlexikon, Fendt 828 Vario)
- AGCO Parts parts book
More from Fendt.