Fendt Farmer 300 Ci service schedule

1. Park level, stop the engine and wait 5 minutes.
2. Pull the dipstick, wipe it, push it fully home and pull it again.
3. Top up towards MAX. Never go above MAX.

Tools: Clean funnel, Rag

1. Wipe each nipple clean first.
2. Grease: lift shaft gears, automatic hitch, mechanical hitch, and the axle knuckle bearings left and right (rear-wheel-drive tractors only).
3. Wipe off the surplus.

Tools: Grease gun, Rag

1. Grease: double universal joints of the front-wheel drive and the front axle bearings front and back (take the weight off the axle first).
2. At 2,000 hours take the cover off each front hub, fill with grease and refit.

Tools: Grease gun, Rag

1. Run the engine until warm (oil about 80 °C), park level and stop the engine.
2. Put the tray under the sump, take the drain plug out and let all the oil run out.
3. Clean the plug, fit it again with a new seal and tighten it.
4. Unscrew the oil filter and catch any oil that runs out.
5. Clean the sealing face. Smear a little oil on the seal of the new filter, screw it on by hand until the seal touches, then a further half turn by hand.
6. Fill with the right oil through the filler cap, keeping everything clean.
7. Start the engine and let it idle until the oil warning goes out. Check the plug and filter for leaks.
8. Stop, wait about 5 minutes and check the dipstick. Top up to the MAX mark but never above it.

Tools: Drain tray (15 L or larger), Oil filter wrench, Socket for the sump plug, Clean funnel, Rag

1. Support the front axle so the wheels turn and switch off the front drive.
2. Drain the differential and each hub (turn the wheel so the hole is at the bottom).
3. Refit the plugs and fill the differential and hubs to the overflow.

Tools: Drain tray, Sockets, Axle stands

1. Change the oil when warm, with the lift down and rams in.
2. Drain the tank through the plug and refit it.
3. Replace the return filter element and the breather filter.
4. Fill with clean oil, then check the level between MIN and MAX with the lift down.

Tools: Drain tray (45 L), Sockets, Clean funnel or pump

1. Make sure the engine is cold (below 50 °C).
2. Take the rocker cover off.
3. Check inlet 0.3 mm and exhaust 0.5 mm. Adjust if needed.
4. Refit the cover with a new gasket. If the engine runs badly, check the injector tips as well.

Tools: Feeler gauges, Spanners and sockets, Torque wrench

1. Release the catches, take the cover off and clean the inside of the housing.
2. Take out the main element and fit the new one, then refit the cover and check the catches.
3. Squeeze the dust valve to clear dust.

Tools: Compressed air line (max 5 bar), Rag

1. Change the oil with the gearbox oil warm.
2. Drain through the plug, clean it and refit with a new seal.
3. Unscrew the filter, lightly oil the seal on the new one and fit it by hand plus half a turn.
4. Fill through the dipstick hole and check the oil reaches the top mark.

Tools: Drain tray (40 L), Filter wrench, Sockets, Funnel or pump

1. Drain the left and right final drives and the front PTO through their plugs. Refit with new seals.
2. Fill through the filler holes to the level mark or overflow.

Tools: Drain tray, Sockets, Funnel or oil pump

1. Stop the engine. No smoking or naked flames.
2. Unscrew the filter cartridge and catch the fuel.
3. Clean the sealing face, lightly oil the seal on the new filter and screw it on by hand until it seats, then half a turn more.
4. Bleed the system with the hand pump until bubble-free fuel flows, tighten the bleed screws, start the engine and check for leaks.

Tools: Container for fuel, Filter wrench, Rag

1. Let the engine cool completely.
2. Open the drain points, drain the coolant into a tray and dispose of it properly.
3. Close the drains, refill with the correct mix and refit a new radiator cap.
4. Run the engine to warm, then top up the expansion tank to between MIN and MAX.

Tools: Drain tray (15 L), Hose clips pliers, Funnel

1. Check the reservoir level against MIN and MAX.
2. Have the fluid changed and the system bled by the Fendt dealer or a brake specialist.

Tools: Brake bleeding kit, Clean container