Ford 3230, 3430, 3930, 4630, 5030 service schedule

Ford 30 series · 1992 on (handbook start date; check your serial plate)

Covers the Ford 3230, 3430, 3930, 4630, 5030 (30 series compacts).

Every maker's service job for the Ford 3230, 3430, 3930, 4630, 5030, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.

Track your 3230, 3430, 3930, 4630, 5030 for free

Versions: 3230 (8x2); 3430 / 3930 / 4630 (8x8 or 16x8); 5030

Service intervals

Job	When
First 50 hour service	every 50 hours
Grease all fittings and pivots	every 50 hours
Drain fuel filter / sediment separator	every 50 hours
Engine oil and filter change	every 300 hours
Hydraulic oil filter(s)	every 300 hours
300 hour checks: transmission level, brakes, belt	every 300 hours
Fuel filter element	every 600 hours
Valve clearance	every 600 hours
Air cleaner	every 600 hours
Rear axle oil change	every 1,200 hours or every year
Transmission oil and internal filter	every 1,200 hours or every year
Front axle differential and hub oil (4WD)	every 1,200 hours or every year
Power steering oil and filter	every 1,200 hours or every year
Coolant change and inhibitor	every 2 years

Service jobs and parts

First 50 hour service

General · every 50 hours

The handbook lists a first service at 50 hours: engine oil and filter, hydraulic inlet filter(s), valve clearance, fan belt tension, brakes and front wheel bearings (2WD), and on 4WD the front differential and hub oil, plus the front-end weight bolts.

Part	Qty	Notes	Part number
Hydraulic oil filter	1	Check your handbook or parts book for the number	check your handbook

Step-by-step

Do the 300 hour engine oil and filter job.
Change the hydraulic inlet filter(s).
Check valve clearance, fan belt tension and brakes.
On 4WD change front differential and hub oil.

Tools: Spanners, Feeler gauges

Grease all fittings and pivots

Chassis · every 50 hours

Every 50 hours. 4WD: drive shaft front bearing and rear trunnion pin, centre bearing and rear fitting, front trunnion pin, upper and lower front swivel bearings. All models: footbrake, clutch and differential lock pedal pivots, three-point linkage. 2WD: front wheel hubs (daily in adverse conditions).

Part	Qty	Notes	Part number
Multi-purpose grease	1	Check your handbook for the grade	check your handbook

Step-by-step

Wipe the nipples clean.
Pump grease into each point in the handbook (figures 20 to 29).
Oil the pivots.

Tools: Grease gun

Drain fuel filter / sediment separator

Fuel · every 50 hours

Every 50 hours drain water and sediment from the glass bowl using the drain plugs, then bleed the injection system.

Step-by-step

Open the drain plug and let contaminated fuel run out.
Close it and bleed the system as the handbook shows.

Tools: Container

Engine oil and filter change

Engine · every 300 hours

The handbook says 300 hours with the filter changed each time. In severe use or below -12 C, change the oil at 150 hours (filter still at 300). With high-sulphur diesel shorten the period: half at 0.5 to 1.0 % sulphur, a quarter at 1.0 to 1.3 %.

Part	Qty	Notes	Part number
Engine oil	1	Check your handbook for the SAE grade (viscosity chart in Section C). Spec: API SF/CD with MIL-L-2104D; API CD with MIL-L-2104C as the minimum. 3230 to 4630: 6.6 L with filter. 5030: printed as 12.5 L with filter, check the dipstick. Aztec Oils match: AGRITEC SUTO 10W-30	check your handbook
Engine oil filter	1	Spin-on, 94 mm long. OE number per Agriline's 5030 engine page. Check against your old filter	84259320

Step-by-step

Warm the engine, stop it and take out the drain plug.
Let the oil drain, then unscrew and bin the filter.
Wipe the filter seat, smear the new seal with clean oil and screw on until the seal touches, then three-quarters of a turn more.
Refit the drain plug and refill through the filler tube. Check the dipstick.

Tools: Drain tray (15 L), Filter wrench

Hydraulic oil filter(s)

Hydraulics · every 300 hours

300 hour service. Screw the new filter on until the face just meets the manifold, then three-quarters of a turn. If the optional engine-mounted pump is fitted, change its filter too.

Part	Qty	Notes	Part number
Hydraulic oil filter	1	Spin-on. OE number per Agriline's 5030 hydraulics page (also D8NNB486CA, F0NN3N976AA)	81869132

Step-by-step

Unscrew and bin the filter(s).
Clean the inlet channel and manifold face.
Smear the seal with oil and fit the new filter(s).

Tools: Filter wrench

300 hour checks: transmission level, brakes, belt

Transmission · every 300 hours

The 300 hour service also covers transmission oil level on the dipstick, footbrake free play (38 mm), handbrake, safety frame bolts and fan belt tension.

Step-by-step

Check the transmission dipstick (8x2 or synchronised).
Check brake free play, handbrake, ROPS bolts and belt tension.

Tools: Spanners

Fuel filter element

Fuel · every 600 hours

600 hour service: close the tank shut-off valve, renew the element and gasket, wash the bowls in clean fuel, then bleed the system.

Part	Qty	Notes	Part number
Fuel filter element	1	CAV type. OE number per Agriline's 5030 engine page (also 84535312, D0NN9N074B)	83937061

Step-by-step

Turn the fuel tank shut-off valve off.
Remove the bowl and element and wash the bowls in clean fuel.
Fit a new element and gasket, open the valve and bleed.

Tools: Container

Valve clearance

Engine · every 600 hours

600 hour service. Cold, inlet 0.36 to 0.41 mm (0.014 to 0.016 in), exhaust 0.43 to 0.48 mm (0.017 to 0.019 in), as printed in the scan. Confirm against your own book.

Step-by-step

Set No. 1 cylinder at top dead centre on the firing stroke.
Check and adjust No. 1 and No. 3 valves.
Turn the engine one revolution and do the rest.

Tools: Feeler gauges, Spanners

Air cleaner

Engine · every 600 hours

Dry type: service the outer element only when the restriction light stays on (within an hour of work) and renew it at 600 hours. Oil bath type: clean every 50 hours. The inner element is renewed at 1,200 hours or annually by a dealer.

Part	Qty	Notes	Part number
Outer air element	1	OE number per Agriline's 5030 engine page	83908365

Step-by-step

Remove the wing nut and outer element.
Fit a new element and check the seal.
Oil bath: wash the gauze and refill the bowl with engine oil to the mark.

Rear axle oil change

Transmission · every 1,200 hours or every year

1200 hours or 12 months. On 4WD drain at the transfer box plug. Rear axle and hydraulic system together hold 32.5 L (8x8 and 16x8) or 45.7 L (8x2 constant mesh); 4WD adds 1.4 L.

Part	Qty	Notes	Part number
Rear axle and hydraulic oil	1	Check your handbook for the grade (Section C); the specification column is garbled in the scan	check your handbook

Step-by-step

Drain the warm oil from the rear axle (or transfer box on 4WD).
Refit the plug and fill to the upper dipstick mark.

Tools: Drain tray (50 L)

Transmission oil and internal filter

Transmission · every 1,200 hours or every year

1200 hours or 12 months. Capacity 8.4 L (16x8), 9.4 L (8x8) or 12.0 L (8x2); creeper gears add 3 L. Synchronised transmission has a pump filter screen held by four bolts (52 Nm).

Part	Qty	Notes	Part number
Transmission oil	1	Check your handbook for the grade (Section C)	check your handbook
Pump filter screen	1	Synchronised transmission only. Check your handbook or parts book for the number	check your handbook

Step-by-step

Drain the warm oil at the transmission plug.
Remove the four screen bolts and fit the new filter, 52 Nm.
Refill, run for a minute and recheck the dipstick.

Tools: Drain tray, Torque wrench

Front axle differential and hub oil (4WD)

Axles · every 1,200 hours or every year

1200 hours or 12 months on 4WD. Differential case 5.5 L, each hub 0.9 L. Also changed in the first 50 hour service.

Part	Qty	Notes	Part number
Front axle oil	1	Check your handbook for the grade (Section C)	check your handbook

Step-by-step

Drain the differential and each hub.
Refill to the level plug.

Tools: Drain tray

Power steering oil and filter

Steering · every 1,200 hours or every year

1200 hours or 12 months; the system holds 2.2 L. Check the level against the bottom of the filler neck every 10 hours.

Part	Qty	Notes	Part number
Power steering oil	1	Check your handbook for the grade (Section C)	check your handbook
Power steering filter and O-ring	1	Check your handbook or parts book for the number	check your handbook

Step-by-step

Disconnect the cooler pipes and pull off the reservoir casing.
Fit a new filter and O-ring.
Refill and bleed by turning the wheel lock to lock.

Tools: Spanners

Coolant change and inhibitor

Cooling · every 2 years

Every two years. 50 % water and permanent antifreeze, with 5 % inhibitor (Ford New Holland FW-15, 473 ml bottle). System 10.4 L (3230 to 4630) or 12.5 L (5030).

Part	Qty	Notes	Part number
Coolant inhibitor	1	Genuine Ford New Holland inhibitor, 473 ml bottle	FW-15

Step-by-step

Drain the radiator and block with the engine cool.
Flush, close the drains and refill 50/50 with inhibitor.
Run the engine and top up.

Tools: Drain tray

Oils, fluids and capacities

System	Oil or spec	Capacity
Engine	Ford M2C121-E diesel (as the handbook names it)
Engine oil	Check your handbook for the SAE grade. API SF/CD with MIL-L-2104D; minimum API CD with MIL-L-2104C	6.6 L with filter (3230 to 4630); 5030 printed as 12.5 L, check the dipstick
Coolant	50/50 water and permanent antifreeze with 5 % inhibitor FW-15; 10.4 L (3230 to 4630), 12.5 L (5030)
Valve clearances	Cold: inlet 0.36 to 0.41 mm, exhaust 0.43 to 0.48 mm (as printed; confirm in your book)
Transmission (8x8 / 16x8)	Check your handbook for the grade (Section C)	9.4 L / 8.4 L; 8x2: 12.0 L
Rear axle and hydraulics	Check your handbook for the grade (Section C)	32.5 L (45.7 L with 8x2); 4WD adds 1.4 L
Front differential (4WD)	Check your handbook	5.5 L
Front hubs (4WD), each	Check your handbook	0.9 L
Hydrostatic steering	Check your handbook	2.2 L
Fuel tank	Diesel	65.1 L

Specifications


Fuel tank	65.1 L

Known problems

Scan accuracy

The source is an OCR scan of the Ford 5030 handbook on ManualsLib. Digits can be misread; check litres and clearances against your own book.

Repair guides

Bleeding the fuel system (Ford 5030 and 30 series compacts) (Easy, 20 to 30 minutes): Engine will not start or stops after a filter change, the tank ran dry, or after injectors or pipes were replaced.
Power steering oil and filter change (Ford 5030 and 30 series compacts) (Moderate, 1 to 1.5 hours): Heavy steering, whining pump, dirty or low steering oil, or the 1,200 hour or 12 month service is due.

The full step-by-step guides are in Farmyard Workshop once you add your tractor.

Parts list with genuine part numbers

Ford 3230, 3430, 3930, 4630, 5030 (30 series compacts) - maker filter/service sheets and parts lists already cited on the site entry; serial splits are in the row notes

Cooling

Part	Part number	Qty	Notes
Coolant inhibitor	FW-15	1	Genuine Ford New Holland inhibitor, 473 ml bottle

Engine service

Part	Part number	Qty	Notes
Engine oil filter	84259320	1	Spin-on, 94 mm long. OE number per Agriline's 5030 engine page. Check against your old filter
Outer air element	83908365	1	OE number per Agriline's 5030 engine page

Fuel

Part	Part number	Qty	Notes
Fuel filter element	83937061	1	CAV type. OE number per Agriline's 5030 engine page (also 84535312, D0NN9N074B)

Transmission and hydraulics

Part	Part number	Qty	Notes
Hydraulic oil filter	81869132	1	Spin-on. OE number per Agriline's 5030 hydraulics page (also D8NNB486CA, F0NN3N976AA)

Sources

Open Farmyard Workshop