John Deere 6230 service schedule
John Deere 6030 series · 2007–2012 (TractorData, 6230)
Covers the John Deere 6230 (also 6330, 6430 and the Premium versions).
Every maker's service job for the John Deere 6230, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.
Track your 6230 for freeVersions: Standard (SyncroPlus, PowrReverser or PowrQuad); Premium (PowrQuad Plus, AutoQuad Plus or IVT)
Service intervals
| Job | When |
|---|---|
| Engine oil and filter change | every 500 hours or every year |
| Cab activated carbon filters (where fitted) | every 500 hours or every year |
| Fuel filters (primary and final) | every 500 hours |
| Transmission and hydraulic oil filters | every 750 hours |
| Front PTO oil filter (where fitted) | every 750 hours |
| Engine air filter elements | every 1,500 hours or every 2 years |
| Cab fresh air and recirculation filters | every 1,500 hours or every 2 years |
| Transmission and hydraulic oil change | when needed |
| Coolant replacement | when needed |
Service jobs and parts
Engine oil and filter change
Engine · every 500 hours or every year
Deere's 6030 series sheets say change the oil and filter after the first 100 hours, then every 500 hours or once a year. The 500-hour interval only applies with Plus-50 II oil, a genuine filter and diesel under 15 ppm sulphur; otherwise change every 250 hours.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Engine oil | 1 | 15W-40 (10W-30, 5W-40 or 0W-40 in colder weather). Plus-50 II, ≈16 L with filter. Aztec Oils match: EMPROTEC EHPD 15W-40 | check your handbook |
| Engine oil filter | 1 | Same number on the standard and Premium sheets | RE504836 |
Step-by-step
- Warm the engine, then park on level ground, lower the linkage, loader and implements to the ground, stop the engine, take the key out and chock the wheels.
- Let it stand a few minutes. Hot oil burns, so wear gloves.
- Remove the sump plug and let the oil drain fully.
- Remove the oil filter, check the old seal came off, and wipe the filter head clean.
- Oil the new filter seal and fit it hand-tight as marked on the filter.
- Refit the drain plug and fill with Plus-50 II to the full mark.
- Run the engine for a minute, check for leaks, stop it and recheck the level.
Tools: Drain tray (20 L), Filter wrench, Spanner for sump plug, Funnel, Rags, Gloves
Cab activated carbon filters (where fitted)
Cab · every 500 hours or every year
Carbon filters protect the driver when spraying. Deere says never clean them, and replace every 500 hours or 1 year, or with the engine primary air filter, whichever comes first.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Activated carbon filter | 2 | Kit AL158986 is also listed | L209778 |
Step-by-step
- Stop the engine and take the key out.
- Open the cab filter covers and remove the carbon filters. Wear gloves and a mask; they may hold spray residue.
- Bag the old filters and dispose of them as chemical waste.
- Fit the new filters and check the covers seal.
Tools: Screwdriver, Dust mask, Gloves
Fuel filters (primary and final)
Fuel · every 500 hours
Deere's sheets say replace both fuel filters every 500 hours. Dirt or water in the fuel damages the injection system.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Primary fuel filter | 1 | RE546336 | |
| Final fuel filter | 1 | RE526557 |
Step-by-step
- Stop the engine, take the key out and chock the wheels. Keep naked flames away.
- Clean around both filters so dirt cannot get in.
- Drain any water from the primary filter bowl into a container.
- Remove the old filters and fit the new ones with clean seals.
- Prime the system with the hand primer as your handbook describes. Never crack open the high-pressure pipes.
- Start the engine and check for leaks.
Tools: Container for fuel, Filter wrench, Rags, Gloves
Transmission and hydraulic oil filters
Transmission · every 750 hours
Deere's sheets say change the transmission and hydraulic filters together after the first 100 hours, then every 750 hours. They protect the pump, valves and gearbox clutches.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Hydraulic oil filter | 1 | AL169573 | |
| Transmission oil filter (not IVT) | 1 | AL221066 | |
| Transmission oil filter (IVT, Premium) | 1 | Instead of AL221066 | AL206482 |
| Hy-Gard for topping up | 1 | Aztec Oils match: AGRITEC UTTO | check your handbook |
Step-by-step
- Park on level ground, lower the linkage, loader and implements fully, stop the engine, take the key out and chock the wheels.
- With the engine off, work the spool valve and linkage controls to relieve hydraulic pressure before opening anything.
- Let hot oil cool before starting; it burns.
- Clean around each filter, then remove both filters and catch the oil.
- Fit new filters with oiled seals, hand-tight.
- Start the engine, run it briefly, stop it and top up Hy-Gard to the correct level. Check both filters for leaks.
Tools: Drain tray, Filter wrench, Rags, Gloves
Front PTO oil filter (where fitted)
PTO · every 750 hours
Deere's sheets list a separate front PTO oil filter, replaced every 750 hours.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Front PTO oil filter | 1 | L114404 |
Step-by-step
- Lower the front linkage and anything on it to the ground, stop the engine, take the key out and chock the wheels.
- Clean around the filter, remove it and catch the oil.
- Fit the new filter with an oiled seal, hand-tight.
- Run the front PTO briefly, stop, check for leaks and top up with Hy-Gard (≈3.5 L system).
Tools: Drain tray, Filter wrench, Rags
Engine air filter elements
Engine · every 1,500 hours or every 2 years
Deere says the primary element may be cleaned up to 5 times and is replaced every 1,500 hours or 2 years. The secondary element is replaced at every fifth primary change or after 1,500 hours, whichever comes first.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Primary air filter | 1 | AL172780 | |
| Secondary (safety) air filter | 1 | AL150288 |
Step-by-step
- Stop the engine and take the key out. Never run the engine with the filter out.
- Open the housing and take out the primary element.
- Only remove the secondary element when it is due; never clean it.
- Wipe the housing out with a damp cloth. Do not blow dirt down the intake.
- Fit the new element(s), check they seat evenly and close the housing.
Tools: Torch, Damp cloth
Cab fresh air and recirculation filters
Cab · every 1,500 hours or every 2 years
Deere says clean them as required and replace every 1,500 hours or 2 years, or with the engine primary air filter, whichever comes first.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Cab fresh air filter, standard | 2 | Heavy-duty alternative: AL177185 on the standard sheet, AL225554 on the Premium sheet | AL225552 |
| Cab recirculation filter (with air con) | 2 | Without air con: L152026 | L214634 |
Step-by-step
- Stop the engine and take the key out.
- Open the filter covers and remove the elements.
- Wear a dust mask. Tap the filters out gently if cleaning, or fit new ones if due.
- Refit the covers and check they seal.
Tools: Screwdriver, Dust mask
Transmission and hydraulic oil change
Transmission · when needed
Deere's sheets give the quantities but not the oil change interval, so check your handbook. Both filters are always changed with the oil. Look at the suction screen in the rear diff housing at the same time for brake debris.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Hy-Gard oil | 1 | UTTO tractor transmission oil. ≈49–52 L, ≈60 L IVT, plus 3 L with four-wheel drive. Aztec Oils match: AGRITEC UTTO | check your handbook |
| Hydraulic oil filter | 1 | Change with the oil | AL169573 |
| Transmission oil filter | 1 | AL221066, or AL206482 with IVT | check your handbook |
Step-by-step
- Park on level ground, lower the linkage, loader and implements fully, stop the engine, take the key out and chock the wheels.
- With the engine off, work the spool valve and linkage controls to relieve hydraulic pressure.
- Let hot oil cool for a while, then drain it from the drain plugs.
- Check and clean the suction screen in the rear diff housing. Brake-lining debris there means the brakes need attention.
- Refit the plugs and fit new transmission and hydraulic filters.
- Fill with Hy-Gard, run the engine, work the hydraulics through their full travel, lower everything and recheck the level.
Tools: Large drain tray (70 L), Spanners, Filter wrench, Pump or funnel, Gloves
Coolant replacement
Cooling · when needed
Cool-Gard II protects against liner pitting, corrosion and frost but wears out. Deere's sheets give the quantity but not the interval, so check your handbook and test the coolant every year.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Cool-Gard II coolant | 1 | ≈29 L with cab, ≈26.5 L without | check your handbook |
Step-by-step
- Only work on a cold engine. Let it cool for at least an hour after work and open the cap slowly.
- Drain the radiator and block into a tray. Dispose of old coolant properly.
- Refit the plugs and fill with Cool-Gard II.
- Run the engine to working temperature with the heater on, let it cool and top up.
Tools: Drain tray, Hose, Coolant test strips
Oils, fluids and capacities
| System | Oil or spec | Capacity |
|---|---|---|
| Engine | John Deere PowerTech E 4.5 L 4-cylinder turbo diesel (4045HL280 or 4045HL287, Tier III, on the 6230) | |
| Engine oil | John Deere Plus-50 or Plus-50 II (viscosity for your climate: check your handbook) | ≈16 L with filter |
| Coolant | John Deere Cool-Gard II: ≈29 L with cab, ≈26.5 L without cab | |
| Valve clearances | Check your handbook. Valve clearance is not on Deere's filter sheets. | |
| Transmission and hydraulics (shared), SyncroPlus or PowrReverser | John Deere Hy-Gard | ≈52 L |
| Transmission and hydraulics (shared), PowrQuad or PowrQuad Plus 16/16 | John Deere Hy-Gard | ≈49 L |
| Transmission and hydraulics (shared), PowrQuad 24/24, PowrQuad Plus 24/24 or AutoQuad Plus | John Deere Hy-Gard | ≈50 L |
| Transmission and hydraulics (shared), IVT (Premium) | John Deere Hy-Gard | ≈60 L |
| Extra with creeper / four-wheel drive / TLS axle | John Deere Hy-Gard | +1 L / +3 L / +3 L (TLS figure from the Premium sheet) |
| Front axle housing (four-wheel drive) | John Deere Hy-Gard | ≈6.5 L |
| Front final drives, each | John Deere Hy-Gard | ≈0.9–0.95 L |
| Front PTO (where fitted) | John Deere Hy-Gard | ≈3.5 L |
| Fuel tank | Diesel | ≈116 L, 160 L, 165 L or 185 L depending on build |
Specifications
| Engine power (6230) | 95 hp (70.8 kW) gross; 75 hp claimed PTO (2007–2009), 76 hp (2010 on) |
| Rated engine speed (6230) | 2,300 rpm |
| Transmissions (6230) | 12-speed synchronised, 16-speed with power shuttle, or 16- or 24-speed partial powershift |
| Hydraulics (6230) | Open-centre load sensing, or closed-centre pressure/flow compensated; 200 bar (2,900 psi); 1 to 3 spool valves |
| Rear lift (6230) | 2,018 kg (4,450 lb) at 610 mm, Category II/III |
| Weight (6230) | 3,893–4,770 kg (8,582–10,515 lb), depending on build |
| Tyres (6230, common) | Front 12.4R24, rear 18.4R30 |
| Tyre pressures | Check your handbook |
Known problems
CAN-bus connectors and ECU
Farmers Weekly reports worn CAN-bus connectors on the 6030 series giving random CommandCenter error codes (often 2000.09). A failed ECU gives similar codes and loses the engine hours; it must be programmed by a main dealer.
Water pump failure
A failed water pump makes the engine overheat fast; the gauge goes into the red and the buzzer sounds. Stop at once.
Brake discs breaking up
Brakes, transmission and back end share one oil. Change worn discs before they break up, and clear the suction screen in the rear diff housing if debris is found.
Six-cylinder models differ
This entry covers the 4-cylinder 6230–6430. The 6530–6930 have the 6.8 L six; the 6830 Premium has its own entry.
Fault codes: What the FMI part of a Deere SPN/FMI code means (also used by New Holland and Case IH engines)
All electronic controllers (J1939)
| Code | Meaning | What to do |
|---|---|---|
| FMI 00 | Reading is far too high (most severe) | Treat as serious. Check the thing it names (temperature, pressure, speed) and stop if it is an engine or oil reading. |
| FMI 01 | Reading is far too low (most severe) | Treat as serious. Check the level or pressure it names; stop if it is oil pressure or coolant. |
| FMI 02 | Signal is erratic, noisy or not believable | Check the sensor plug and wiring for damage, water or a loose pin. If it stays, dealer. |
| FMI 03 | Voltage too high or shorted to a power wire | Usually a wiring or sensor fault. Check the plug is fully home; otherwise dealer. |
| FMI 04 | Voltage too low or shorted to ground | Usually a wiring or sensor fault, chafed wire or wet plug. Dealer if it stays. |
| FMI 05 | Open circuit or current too low | Broken wire, unplugged connector or failed component. Check the plug; otherwise dealer. |
| FMI 06 | Short circuit or current too high | Damaged wire or failed component pulling too much current. Dealer. |
| FMI 07 | Mechanical part not responding or out of position | Something moved by the controller is stuck or not following. Dealer. |
| FMI 08 | Signal frequency or pulse width wrong | Speed or position sensor signal is wrong. Check the sensor plug and wiring; dealer. |
| FMI 09 | Signal arriving too slowly, late or missing | A message or sensor update has stopped. Check connectors; dealer. |
| FMI 10 | Signal changing too fast | Signal is jumping abnormally. Check connectors; dealer. |
| FMI 11 | Fault present, cause not identified | Dealer. |
| FMI 12 | Controller or device itself has failed | Dealer. Do not keep clearing the code. |
| FMI 13 | Out of calibration | The sensor or control needs calibrating. Dealer. |
| FMI 14 | Special instruction (meaning set by the maker) | Look up the exact SPN/FMI pair; dealer. |
| FMI 15 | Reading a little too high (least severe warning) | Early warning. Find the cause before it gets worse. |
| FMI 16 | Reading too high (moderately severe warning) | Warning level. Find the cause now and ease off the work. |
| FMI 17 | Reading a little too low (least severe warning) | Early warning. Find the cause before it gets worse. |
| FMI 18 | Reading too low (moderately severe warning) | Warning level. Check levels now and ease off the work. |
| FMI 19 | Data link (CAN bus) error between controllers | Check battery terminals and plugs; dealer if it stays. |
| FMI 31 | The named condition exists (used as an on/off flag) | Read the SPN description to see what condition is flagged. |
Fault codes: PowerTech 4.5 L / 6.8 L electronic engines: common SPN/FMI codes
Engine controller (ECU)
| Code | Meaning | What to do |
|---|---|---|
| 000028.03 | Throttle (B) signal voltage too high | Check the throttle pedal or lever plug is fully pushed in and not damaged; dealer if it stays. |
| 000028.04 | Throttle (B) signal voltage too low | Check the throttle plug and wiring; dealer if it stays. |
| 000029.03 | Throttle (A) signal voltage too high | Check the throttle plug and wiring; dealer if it stays. |
| 000029.04 | Throttle (A) signal voltage too low | Check the throttle plug and wiring; dealer if it stays. |
| 000091.03 | Throttle input voltage too high | Check the throttle plug and wiring; dealer if it stays. |
| 000091.04 | Throttle input voltage too low | Check the throttle plug and wiring; dealer if it stays. |
| 000091.09 | Throttle signal invalid | Check the throttle plug and wiring; dealer if it stays. |
| 000097.00 | Water in fuel detected all the time | Drain the fuel water separator now, using the drain tap on the filter housing, until clean fuel runs. Dealer if it keeps returning. |
| 000097.16 | Water in fuel detected | Drain the fuel water separator (drain tap on the filter housing) until clean fuel runs. |
| 000100.01 | Engine oil pressure extremely low | Stop the engine at once. Check the oil level and look for leaks. If the level is correct, do not run it again: call your dealer. |
| 000100.18 | Engine oil pressure moderately low | Stop and check the oil level and for leaks. Top up to the mark with the correct grade if low. If the level is right and the warning stays, do not work the engine: dealer. |
| 000100.03 | Engine oil pressure sensor voltage too high | Sensor or wiring fault. Check the sensor plug; dealer if it stays. Check the oil level now to rule out a real pressure problem. |
| 000100.04 | Engine oil pressure sensor voltage too low | Sensor or wiring fault. Check the sensor plug; dealer if it stays. Check the oil level now to rule out a real pressure problem. |
| 000105.00 | Manifold (intake) air temperature extremely high | Ease off the load, check the cooler and radiator for chaff and mud, and the air intake for blockage. |
| 000105.16 | Manifold air temperature moderately high | Ease off the load, clean the radiator and cooler screens; dealer if it stays. |
| 000105.03 | Manifold air temperature sensor voltage too high | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000105.04 | Manifold air temperature sensor voltage too low | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000107.00 | Air filter restricted | Stop at a safe time, clean or replace the air filter element as the handbook shows, and check the intake hose for splits. |
| 000110.00 | Engine coolant temperature extremely high | Stop working, idle for a minute to cool, then stop. Let it cool before opening anything. Check the coolant level, and clean the radiator and grille screens. Call your dealer if it comes back. |
| 000110.16 | Engine coolant temperature moderately high | Ease off the load and clean the radiator, grille and cooler screens. Check the coolant level when cold. Dealer if it keeps happening. |
| 000110.15 | Engine coolant temperature high (least severe) | Early warning: ease off the load, clean the radiator and grille screens, check the coolant level when cold. |
| 000110.03 | Engine coolant temperature sensor voltage too high | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000110.04 | Engine coolant temperature sensor voltage too low | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000111.01 | Engine coolant level low | Stop. Wait for the engine to cool fully, then check and top up the coolant to the mark and look for leaks. If it keeps dropping, dealer. |
| 000158.17 | ECU power-down error (battery power was removed too soon after switching off) | Switch off with the key and wait before isolating the battery. Check the battery terminals are tight and clean. |
| 000171.03 | Ambient air temperature signal out of range | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000174.00 | Fuel temperature extremely high | Ease off the load; dealer if it stays. |
| 000174.16 | Fuel temperature moderately high | Ease off the load; dealer if it stays. |
| 000174.15 | Fuel temperature high (least severe) | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000174.03 | Fuel temperature sensor voltage too high | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000174.04 | Fuel temperature sensor voltage too low | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000189.00 | Engine speed derate (power is being limited) | Look for other active codes; the engine is limiting itself for protection. Dealer. |
| 000190.00 | Engine overspeed, extreme | Stop the engine. Do not restart until your dealer has checked it. |
| 000190.16 | Engine overspeed, moderate | Ease off and avoid over-revving on downhills; dealer if it returns. |
| 000620.03 | Sensor supply voltage too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000620.04 | Sensor supply voltage too low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000629.13 | ECU (engine controller) error | Switch off and restart once. If it returns, dealer. |
| 000639.13 | CAN bus error (controllers not talking) | Check the battery terminals and engine harness plugs; dealer if it stays. |
| 000729.03 | Inlet air heater signal high | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000729.05 | Inlet air heater signal low | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000970.31 | Auxiliary engine shutdown switch is active | Check whether an external shutdown switch has been operated or is stuck. |
| 000971.31 | External engine derate switch is active | Check whether an external derate switch has been operated or is stuck. |
| 001109.31 | Engine shutdown warning: the engine is about to shut down | Stop and park safely now, before the engine stops itself. Check oil, coolant and look for other codes. |
| 001110.31 | Engine shutdown (protection has stopped the engine) | Leave it stopped. Check the oil and coolant levels and the other codes for the cause; dealer. |
| 001568.02 | Torque curve selection switch invalid | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 001569.31 | Fuel derate (power limited) | Look for other active codes; dealer. |
| 002000.13 | Security violation (controller security check failed) | Dealer: the controller or software does not match. |
Fault codes: PowerTech engines with Denso high-pressure common rail ('475'): injector, rail and pump SPN/FMI codes
Engine controller (ECU), injectors and common-rail pump
| Code | Meaning | What to do |
|---|---|---|
| 000094.03 | Fuel rail pressure sensor voltage too high | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000094.04 | Fuel rail pressure sensor voltage too low | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000094.10 | Fuel rail pressure loss detected | Check the fuel level and filters. Never slacken high-pressure fuel lines with the engine running or just stopped. Dealer. |
| 000094.13 | Fuel rail pressure higher than expected | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000094.17 | Fuel rail pressure not developed | Check the fuel level, filters and for air in the supply. If it will not start or keeps stalling, dealer. |
| 000611.03 | Electronic injector wiring shorted to power | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000611.04 | Electronic injector wiring shorted to ground | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000627.01 | Electronic injector supply voltage problem | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.07 | Crank and pump timing moderately out of sync | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.02 | Pump position sensor input noise | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.08 | Pump position sensor input missing | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.10 | Pump position sensor input pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.02 | Crank position input noise | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.08 | Crank position input missing | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.10 | Crank position input pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000676.03 | Glow plug relay voltage high | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000676.05 | Glow plug relay voltage low | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 001080.03 | Fuel rail pressure sensor supply voltage too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001080.04 | Fuel rail pressure sensor supply voltage too low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001347.03 | Pump return shorted high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001347.05 | Pump control valve error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001347.07 | Fuel rail pressure control error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001568.02 | Torque curve selection invalid | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 001069.09 | Tyre size invalid | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 001069.31 | Tyre size error | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000651.05 | Cylinder 1 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000651.06 | Cylinder 1 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000651.07 | Cylinder 1 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000652.05 | Cylinder 2 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000652.06 | Cylinder 2 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000652.07 | Cylinder 2 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000653.05 | Cylinder 3 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000653.06 | Cylinder 3 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000653.07 | Cylinder 3 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000654.05 | Cylinder 4 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000654.06 | Cylinder 4 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000654.07 | Cylinder 4 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000655.05 | Cylinder 5 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000655.06 | Cylinder 5 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000655.07 | Cylinder 5 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000656.05 | Cylinder 6 injector circuit open | Check the injector plug and wiring at the engine; if the engine runs rough or misfires, dealer. |
| 000656.06 | Cylinder 6 injector circuit shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000656.07 | Cylinder 6 injector delivery failure | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
Fault codes: PowerTech engines with Stanadyne DE10 pump: pump-specific SPN/FMI codes
Engine controller (ECU) and rotary fuel injection pump
| Code | Meaning | What to do |
|---|---|---|
| 001076.00 | Pump control valve closing too slowly | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.01 | Pump control valve closing too quickly | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.03 | Pump solenoid current too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.05 | Pump solenoid circuit open | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.06 | Pump solenoid circuit severely shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.07 | Pump control valve closure not detected | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.10 | Pump solenoid circuit moderately shorted | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001076.13 | Pump current decay time invalid | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.02 | Engine position sensor noise detected | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.08 | Engine position sensor signal missing | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.10 | Engine position sensor pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.01 | Timing (crank) sensor signal pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.02 | Crank position input noise | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.10 | Crank position input pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000627.04 | ECU unswitched (permanent) power missing | Check the engine controller fuse and battery feed; dealer if it stays. |
| 001079.03 | Sensor supply voltage too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001079.04 | Sensor supply voltage too low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000084.31 | Vehicle speed mismatch | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000091.07 | Throttle calibration invalid | The dealer will need to recalibrate the throttle. |
| 000091.10 | Throttle voltage low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000091.14 | Throttle voltage out of range | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000190.01 | Engine speed below normal, most severe | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
Fault codes: PowerTech engines with Bosch VP44 pump: pump-specific SPN/FMI codes
Engine controller (ECU) and electronic VP44 injection pump
| Code | Meaning | What to do |
|---|---|---|
| 000094.01 | Fuel supply pressure extremely low | Check the fuel level, the fuel filters (change if overdue) and for air leaks in the supply line. Dealer if it stays. |
| 000094.18 | Fuel supply pressure moderately low | Check the fuel level and filters and for air leaks in the supply line. |
| 000094.03 | Fuel supply pressure sensor voltage too high | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000094.04 | Fuel supply pressure sensor voltage too low | Check the sensor plug is fully home and the wiring is undamaged; dealer if it stays. |
| 000084.02 | Vehicle speed mismatch | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000629.19 | ECU to pump communication error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000632.02 | Fuel shut-off error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000632.05 | Fuel shut-off non-functional | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.02 | Pump position input noise | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.08 | Pump position input missing | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000636.10 | Pump position input pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.02 | Crank position input noise | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.08 | Crank position input missing | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000637.10 | Crank position input pattern error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000810.02 | Calculated vehicle speed input noise | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 000898.09 | Vehicle speed invalid or missing | Note the code. If it is not active now or goes away after a restart, mention it at the next service; if it stays, tell your dealer. |
| 001069.02 | Tyre size error (wrong size set for the speed calculation) | The dealer can set the correct tyre size. |
| 001076.02 | Pump has detected a defect | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001077.07 | Pump is trying to fuel without being commanded | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001077.11 | Pump supply voltage out of range | Check the battery and charging; dealer if it stays. |
| 001077.12 | Pump self-test error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001077.19 | Pump detected a communication error | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001077.31 | Pump has put the engine into protection | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001078.07 | ECU and pump timing moderately out of sync | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001078.11 | ECU and pump speed out of sync | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001078.31 | ECU and pump timing extremely out of sync | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001079.03 | Sensor supply 1 voltage too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001079.04 | Sensor supply 1 voltage too low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001080.03 | Sensor supply 2 voltage too high | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001080.04 | Sensor supply 2 voltage too low | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 001485.02 | Pump power relay fault | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
| 000627.04 | ECU unswitched power missing | Check the engine controller fuse and battery feed; dealer if it stays. |
| 000174.31 | Fuel temperature sensor faulty | Finish the job safely, then have your dealer read the stored code. Note the full code and whether it comes back. |
Repair guides
- CAN-bus connector faults and random error codes (Moderate, About 1 hour per connector): Random error codes on the CommandCenter (2000.09 in particular), warnings that come and go, functions dropping out, or engine hours missing from the dash.
- Water pump failure and replacement (Moderate, About 3 hours): Temperature gauge goes straight into the red with the warning buzzer, coolant from the pump weep hole, a noisy pump bearing or a wobbling pulley.
- Rear brake discs worn or breaking up (Hard, About a day per side): Weak or uneven braking, long pedal travel, dark paste or flakes in the transmission oil, or filters blocking soon after a change.
- Four-wheel-drive front axle: kingpins, track rods and pivot (Hard, 1 hour to check; most of a day for kingpins): Play at the front wheels, wandering, a clunk when steering, uneven tyre wear, or oil weeping from a hub seal.
- Starter: no crank or slow crank (Moderate, 1–3 hours): Click but no crank, slow cranking, or nothing at all when the key is turned.
The full step-by-step guides are in Farmyard Workshop once you add your tractor.
Parts list with genuine part numbers
John Deere Maintenance and Wear Parts Catalog PC4957G (6030 series, ed. 31-Aug-2010; German text, names translated)
Filters
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Air filter | AL150288 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Air filter | AL172780 | 1 | length 183 mm (7-7/32"). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Filter element | RE529644 | 1 | (E). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Filter element | RE529643 | 1 | (E) only 6534. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Oil filter | AL156625 | 1 | length 151,6 mm (5-31/32"). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Oil filter | AL169573 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Air filter | AL177184 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Air filter | AL177185 | 2 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Filter element | L152026 | 2 | (B). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Filter | L155288 | 2 | (C). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Fuel filter | RE526557 | 1 | not for 6534. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Activated carbon filter | L156225 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
Engine
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Hose | L167575 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | L170861 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cap | L167674 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 9M7774 | 5 | M6X12. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rail | L168498 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Nut | L168085 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fan shroud | L176302 | 1 | ( substitutes for L168523). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 37M7305 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7250 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | L116423 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Insulator | L175735 | 2 | ( substitutes for L151665). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lining | L154938 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Lining | L154939 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Clamp | AR48236 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Filler cap | AL78005 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rivet | L168497 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Drain plug | AL155781 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L169998 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L169999 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Drain tap | AL176130 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cap | L169974 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
Electrical
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Battery (dry charged) | AL75644 | 1 | 12V,110AH,500A,MARKEDAL75854. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Battery (dry charged) | AL119623 | 1 | 12V,154AH,700A,MARKEDAL119622. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hook bolt | L170437 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lock nut | 14M7397 | 2 | M6. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hook bolt | L116540 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Stud | 2M7058 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 9M7786 | 1 | M10X30. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Decal | R116617 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Starter kit | RE527400 | 1 | MARKEDRE526375. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Starter motor (exchange) | SE501868 | 1 | (B). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Nut | 4M7274 | 1 | M10. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring washer | 2M7135 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cable tie | H77698 | 1 | length 360 mm (14.2"). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Decal | T146102 | 1 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fuse | 57M7689 | as required | 10A. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fuse | 57M7690 | as required | 15A. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fuse | 57M7691 | as required | 20A. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fuse | 57M8163 | as required | 30A. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fuse | 57M7993 | as required | (A)70A. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Bulb | AT130104 | as required | H3,12V/55W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | 57M7166 | as required | H4,12V/60/55W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | R136239 | as required | 12V/55W( substitutes for 57M7358). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | 57M6394 | as required | 12V/5W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb holder | L64144 | as required | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | 57M7013 | as required | 12V,10W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | 57M7019 | as required | H1,12V/55W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | R133301 | as required | 12V-21W( substitutes for 57M7014). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | M136357 | as required | 12V-21/5W( substitutes for 57M7011). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Bulb | 57M6498 | as required | 12V/5W. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
Transmission
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Taper bearing cup | L154620 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Taper bearing cone | AL156506 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Wear ring | L76058 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Radial oil seal | AL158922 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Radial oil seal | AL69712 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Taper bearing cup | L154621 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Taper bearing cone | AL156503 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Snap ring | L76059 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
Brakes
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Piston | L111978 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L56243 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L56246 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Brake disc | AL171954 | 2 | TK=4,9 mm. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Brake disc | AL171955 | 2 | (A)TK=5,9 mm. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Washer | L114053 | 2 | TK=22 mm. Listed for the wider 6030-series group (cylinder/series column); check serial |
Hydraulics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| O-ring | L59904 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fitting | R94882 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7048 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | 38H5013 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7040 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | 38H5001 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7043 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | 38H5010 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T77932 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Oil line | AL167658 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T77858 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL169555 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T77814 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7039 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | AL168801 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T59014 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7576 | 4 | M10X30,(10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Elbow fitting | AL172007 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL176422 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Clamp | L171572 | 2 | ( substitutes for L153419). Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T77613 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic oil reservoir | AL110340 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Set screw | L100271 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L77586 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fitting | L110064 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Clamp | L112762 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7103 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7100 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7041 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Oil pump | AL166637 | 1 | 28CM3. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Oil pump | AL166639 | 1 | 45CM3. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic pump (exchange) | PG200867 | 1 | (A)45CM3. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7789 | 2 | M12X30. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Gasket kit | AL158422 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | T42302 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Drain plug | 15M7079 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Parts kit | AL158423 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | L174060 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL180156 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange fitting | L201123 | 1 | ( substitutes for L170842APPL). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7785 | 2 | M10X25,(10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Gasket | L77317 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7045 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | 38H5193 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Oil line | AL178099 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | 38H5002 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | U41966 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7660 | 3 | M8X20. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange fitting | L174175 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L170402 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | L79006 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | L171593 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange fitting | L173942 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | L173940 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL172931 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic pump | AL156335 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Elbow fitting | 38H5019 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | 51M7047 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | L176627 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL180946 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic pump | AL180950 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Stud | L201164 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange fitting | L176623 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Nut | 14M7274 | 2 | M10. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7044 | 3 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M8533 | 4 | M10X25. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hose | AL180125 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic hose | AL174929 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange fitting | L170842 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| O-ring | L34995 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M8300 | 2 | M8X40. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic coupler socket | AL166181 | as required | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seal kit | AL166745 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Seal kit | AL112953 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Cover | L112370 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic coupler socket | AL202353 | 1 | INCLKEY5( substitutes for AL172003,AL178991). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hydraulic coupler socket | AL202354 | 1 | INCLKEY5( substitutes for AL172004,AL178992). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seal kit | AL205022 | 1 | ( substitutes for AL166745). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Seal kit | AL173668 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Cover | AL177681 | as required | (B)MARKEDII. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cover | AL177682 | as required | (C)MARKEDIII. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cover | AL177683 | as required | (D)MARKEDIV. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rubber boot | L170078 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring clip | L167490 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rubber boot | L170077 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring clip | L158630 | as required | (E). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Sleeve | L170081 | as required | (E). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plug | L170555 | as required | (A)MARKEDI. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plug | L170556 | as required | (B)MARKEDII. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plug | L170557 | as required | (C)MARKEDIII. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plug | L102157 | as required | (D)MARKEDIV. Listed for the wider 6030-series group (cylinder/series column); check serial |
Front axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Radial oil seal | AL161315 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Snap ring | 0M7115 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Radial oil seal | AL161384 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
Operator's station
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Gas strut | AL174356 | 1 | (A)( substitutes for AL78987). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Gas strut | AL174358 | 1 | (B). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Ball stud | R237474 | 1 | ( substitutes for R97588). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Gas strut | AL174357 | 1 | (C)( substitutes for AL114803). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Ball stud | L113715 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Gas strut | AL174088 | 1 | (D). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Ball stud | L78979 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Windscreen | L171336 | 1 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171338 | 1 | (B). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171333 | 1 | LH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171334 | 1 | RH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Door | L169103 | 1 | RH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171927 | 1 | RH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171928 | 1 | LH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Window glass | L171335 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Holder | AL77485 | 1 | LH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Holder | AL77486 | 1 | RH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cap | L79775 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rear view mirror | AL78021 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Mirror glass | L79776 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Bulb holder | L79777 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Holder | L79778 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 21M7423 | 2 | M6X30. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7362 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | L153130 | 4 | (10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Parts kit | AL78834 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Console | AL77483 | 1 | LH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Console | AL77484 | 1 | RH. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Frame tube | L78174 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Knob | L78176 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rod | L78173 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adapter fitting | L79784 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 21M7430 | 1 | M6X16. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7660 | 4 | M8X20. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cap | L38797 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7053 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 19M7827 | 1 | M16X80,(10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hex bolt | 19M7720 | 1 | M16X80,(10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Console | AL117577 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Flange nut | 14M7291 | 1 | M16. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Wiper blade | AL153660 | 1 | (A)(B)(C) length 500 mm. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Wiper blade | AL153661 | 1 | (A) length 600 mm. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Wiper arm | AL153662 | 1 | (A)(B). Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Screw | 9M7867 | 4 | M8X25(10.9). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seat belt | AL155361 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Washer | 24M7252 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lock nut | R168723 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spacer | L171439 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | L171438 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seat belt | AL201826 | 1 | FI. Listed for the wider 6030-series group (cylinder/series column); check serial. Wear/service part |
| Cushion | AL116993 | 1 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Cushion | AL116992 | 1 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 1M7467 | as required | M5X16. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Damper | AL117341 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seat suspension | AL117349 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Adjuster | AL117348 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Damper | AL117346 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Strap | L61612 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rivet | L39011 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plate | L38890 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Rod | L38862 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Nut | L38861 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Holder | AL36643 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Extension spring | T82227 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Fork | AL38526 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Needle bearing | AL64034 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Pin | AL41471 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Roller | L38855 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Bearing | L42041 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Plate | L38853 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Pin | L63562 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Snap ring | 40M7082 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring | AL70626 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seat suspension | AL117340 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Seat suspension | AL117343 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring nut | L61627 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Actuator | AL117342 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Parts kit | AL117369 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 37M7293 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Extension spring | L61599 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | L61615 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Clamp | L61607 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spring | L61610 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Nut | 14M7273 | 1 | M8. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Bush | L61601 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Console | L113889 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Console | L113888 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 12M1646 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hex bolt | 19H2247 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Decal | R168102 | 2 | (A). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Decal | R168701 | 2 | (B). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Decal | R168702 | 2 | (C). Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 03M7099 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hex bolt | 19M7560 | 1 | M6X16. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7251 | 2 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lock nut | 14M7165 | 2 | M6. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lock nut | 14M7376 | 1 | M6. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Screw | 03M7317 | 1 | M6X35. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Clamp | L79430 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Spacer | L172629 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Washer | 24M7178 | 4 | Listed for the wider 6030-series group (cylinder/series column); check serial |
| Lock nut | 14M7167 | 4 | M10. Listed for the wider 6030-series group (cylinder/series column); check serial |
| Hood | L113438 | 1 | Listed for the wider 6030-series group (cylinder/series column); check serial |
Sources
- Plus-50 II grades (15W-40, 10W-30, 5W-40, 0W-40) and air-temperature chart (John Deere Plus-50 II data sheet)
- Plus-50 II 15W-40 data sheet (John Deere Australia/NZ)
- Filter numbers, intervals and capacities, standard 6230–6430 (John Deere filter overview, Nov 2020)
- Same sheet, April 2021 release (no heavy-duty fresh air filter listed)
- Premium 6230–6430: IVT filter, IVT and AutoQuad Plus capacities, TLS (John Deere filter overview, Apr 2021)
- Years, power, gearboxes, hydraulics, lift, weight and tyres (6230)
- Engine models and rated speed (6230)
- 6030 series CAN-bus, ECU, water pump and brake faults (Farmers Weekly)
- JD Wartungs- und Verschleissteilekatalog PC4957G (6030 series, European market, 31-Aug-2010), Scribd copy; German part names translated
More from John Deere.