Landini Legend 130 service schedule

1. Clean each nipple and check the ball is free.
2. Grease the front axle pivot (2 points) and the front axle drive shaft bearing.
3. On the Techno, give the PTO clutch sleeve no more than two strokes.
4. Grease the lift and three-point linkage (7 points) while you are there.
5. Wipe off the surplus.

Tools: Grease gun, Rags

1. Warm the engine, park on level ground, lower implements, apply the handbrake and stop the engine.
2. Remove the sump drain plug and drain the oil. It will be hot.
3. Unscrew the oil filter cartridge, smear the new seal with oil and screw it on by hand.
4. Refit the drain plug at 3.5 daNm (35 N·m).
5. Fill with the right oil to the MAX mark on the dipstick.
6. Run the engine, check for leaks, let the oil settle and recheck the level.

Tools: Drain tray (20 L), Socket for the sump plug, Torque wrench, Filter wrench, Funnel, Rags, Gloves

1. Lower implements, stop the engine and apply the handbrake.
2. Unscrew the two intake cartridges, oil the new seals and screw the new ones on by hand.
3. Unscrew the delivery filter holder, change the inner element, oil the seal and washer and refit the holder hand tight.
4. Start the engine, check for leaks and top up the transmission oil to the dipstick mark.

Tools: Filter wrench, Drain tray, Rags

1. Stop the engine and apply the handbrake.
2. Unscrew the holder and remove the cartridge.
3. Smear oil on the new seal and washer, fit the new cartridge and screw the holder hand tight.
4. Start the engine and check for leaks.

Tools: Filter wrench, Drain tray, Rags

1. Stop the engine and keep naked flames away.
2. Remove the three cartridges and clean the filter bowls.
3. Fit the new cartridges with new seals.
4. Bleed the air out with the hand primer on the fuel lift pump, then start the engine and check for leaks.

Tools: Container, Spanners, Rags

1. Work on a cold engine and remove the rocker cover.
2. Turn the engine to set each valve in turn, following the Perkins workshop manual.
3. Set inlet valves to 0.20 mm and exhaust valves to 0.45 mm.
4. Refit the cover with a sound gasket. If unsure, have the dealer do it.

Tools: Feeler gauges, Spanners, Engine turning tool

1. Work the tractor so the oil is warm, then park level and lower the linkage.
2. Remove plugs 1, 2 and 3 at the lowest points of the gearbox and rear axle and drain the oil.
3. Clean the plugs and refit them.
4. Change the intake filters and the delivery filter.
5. Fill with clean oil to the dipstick mark, run the engine and recheck.

Tools: Large drain tray (100 L), Spanners, Filter wrench, Oil pump

1. Park level and stop the engine.
2. Remove the differential drain plug, drain the oil, refit the plug and fill to the level plug.
3. Turn each wheel so the final drive plug is at the bottom and drain it.
4. Turn the plug to the horizontal (hub centre-line) position and fill to the hole.
5. Refit all plugs and check for leaks.

Tools: Drain tray, Spanners, Oil pump or squeeze bottle

1. With the engine cold, open the radiator and cylinder block drain plugs.
2. Flush the system with clean water, then close the drains.
3. Fill at about 10 L a minute, refit the cap and turn on the cab heater.
4. Run the engine at 1,000 rpm for a few minutes, recheck the level and top up.

Tools: Large drain tray, Funnel, Antifreeze tester

1. Remove the old cab air filter.
2. Fit a new one in its place the right way round.

Tools: Screwdriver

1. When the fuel tank is nearly empty, remove the drain fitting, drain the sludge and bleed the fuel system if needed.
2. Book the tractor in to have the injectors, starter motor and alternator checked.
3. Ask them to check the steering cylinder ball joint nuts are at the right torque.

Tools: Dealer service, Spanner for the tank fitting

1. Stop the engine and open the filter container cover.
2. Lift out the outer element. Fit a new one if it has been cleaned six times, is a year old or shows holes against a lamp.
3. To clean it, blow dry air (under 6 bar) from the inside out, or wash it in water and non-foaming detergent and dry it at no more than 50 °C.
4. Never clean the inner element; replace it every third outer cleaning.
5. Clean the housing, refit the elements and check the rubber drain valve is clear.

Tools: Compressed air under 6 bar, Torch, Rags