Massey Ferguson 5455 service schedule
Massey Ferguson 5400 series · 2005–2013
Every maker's service job for the Massey Ferguson 5455, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.
Track your 5455 for freeVersions: Tier 2 engine (Perkins 1104C-44T); Tier 3 engine (from about 2008; listed as 1104D-E44TA by one supplier)
Service intervals
| Job | When |
|---|---|
| Drain water from the fuel tank | every 50 hours |
| Engine oil and filter change | every 250 hours or every year |
| Fuel filters (primary and secondary) | every 500 hours or every year |
| Air cleaner elements | every 500 hours or every year |
| Valve lash check and adjust | every 1,000 hours |
| Coolant change | every 3,000 hours or every 2 years |
| Transmission and hydraulic oil and filter change | when needed |
| Front axle and final drive oil change (4WD) | when needed |
Service jobs and parts
Drain water from the fuel tank
Fuel · every 50 hours
The Perkins 1104D handbook says drain water and sediment from the fuel tank every 50 hours or weekly. Water in diesel causes rust and injector damage.
Step-by-step
- Stop the engine, take the key out and keep naked flames away.
- Open the tank drain (if fitted) and let water and sediment run out until clean fuel shows.
- Close the drain and dispose of the waste properly.
Tools: Container, Rags
Engine oil and filter change
Engine · every 250 hours or every year
The Perkins 1104D handbook lists engine oil and filter at 250 hours and also at 500 hours or 1 year; which applies depends on the engine build and use, and the MF handbook was not available. 250 hours is used here to be safe: check your handbook. Change the filter every time.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Engine oil | 1 | ≈7.5 L; grade: check your handbook | check your handbook |
| Oil filter | 1 | Spin-on, 175 mm long (Perkins 2654407); Agriline lists it for the 5455 | 1447031M2 |
Step-by-step
- Park on level ground, lower implements to the ground, stop the engine, take the key out and chock the wheels.
- Perkins says drain the oil warm, never cold. Run the engine to working temperature, stop it and let it stand a few minutes. Hot oil burns, so wear gloves.
- Remove the sump plug and let the oil drain fully into a container big enough to hold it. Refit the plug.
- Remove the old filter, check the seal came off with it and wipe the head clean.
- Oil the new seal and fit the filter by hand as marked on it.
- Fill to the full mark. Do not over- or under-fill; Perkins warns this can damage the engine.
- Run the engine, check for leaks, stop it and recheck the level.
Tools: Drain tray (15 L), Spanner for sump plug, Filter wrench, Funnel, Rags, Gloves
Fuel filters (primary and secondary)
Fuel · every 500 hours or every year
The Perkins 1104D handbook says replace the primary filter (water separator) element and the secondary filter every 500 hours or 1 year, and drain the water separator daily. Dirt and water wreck the injection system.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fuel filter | 1 | Listed by a parts seller for 1104D-E44T engines in the 5455 (Perkins 2656F843); Agriline notes its Tier 2 kit filter replaces the complete canister. Check yours | 4226599M1 |
| Primary filter / water separator element | 1 | Tier 3 tractors. Tier 2 tractors have a single cartridge, 4224811M1, that replaces the whole canister | 4226708M1 |
Step-by-step
- Stop the engine, take the key out and chock the wheels. Keep naked flames away.
- Clean around the filters so no dirt can get in.
- Drain the water separator, then remove the old filter(s).
- Fit the new filters with their seals, hand-tight.
- Prime the fuel system as the handbook describes before starting.
- Start the engine and check for leaks.
Tools: Filter wrench, Container for fuel, Rags
Air cleaner elements
Engine · every 500 hours or every year
The Perkins 1104D handbook says clean or replace the dual-element air cleaner every 500 hours or 1 year, or sooner when the restriction indicator shows. Check the pre-cleaner daily.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Inner (safety) air filter | 1 | Agriline lists this for the 5455; 3901465M2 also listed | 3901465M1 |
| Outer air filter | 1 | Steep-nose bonnet; pairs with inner 3901465M1. Standard-bonnet Tier 2 tractors take outer 3901475M1 with inner 3901476M1 | 3901464M1 |
Step-by-step
- Stop the engine and take the key out. Never run the engine with the element out.
- Open the housing and take out the outer element. Only remove the inner element when replacing it.
- Wipe the housing with a damp cloth; do not let dirt fall into the intake.
- Fit the new elements, check the seals and close the housing. Reset the restriction indicator if fitted.
Tools: Torch, Damp cloth
Valve lash check and adjust
Engine · every 1,000 hours
The Perkins 1104D handbook says check the valve lash at the first 500 hours, then every 1,000 hours, and that a trained person should do it. Wrong lash costs power and can burn valves. The figure depends on the engine: the Perkins 1104D electronic engine (Tier 3) is 0.35 mm inlet and exhaust, but the Perkins 1103/1104 industrial engine manual gives 0.20 mm inlet and 0.45 mm exhaust, cold, which is the figure for the mechanical 1104C of the Tier 2 tractor. Check the engine plate before setting anything.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Rocker cover gasket | 1 | 4224954M1 |
Step-by-step
- Stop the engine, take the key out and chock the wheels. Let the engine cool before working on it.
- Remove the rocker cover.
- Turn the engine until the valves you are checking are fully closed.
- Check with a feeler gauge: 0.35 mm (0.013 in) inlet and exhaust on the 1104D. Confirm the figure for your engine first.
- Adjust if needed, lock the nut and recheck, then refit the cover with a sound gasket.
Tools: Feeler gauges, Spanners, Engine turning tool
Coolant change
Cooling · every 3,000 hours or every 2 years
The Perkins 1104D handbook says change commercial heavy-duty coolant every 3,000 hours or 2 years (Perkins long-life coolant lasts 12,000 hours or 6 years), and test and top up the coolant additive every 500 hours or 1 year.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Coolant | 1 | ≈16.6 L; type: check your handbook | check your handbook |
Step-by-step
- Only work on a cold engine. Turn the header tank cap slowly to let pressure out.
- Drain the radiator and block into a tray. Dispose of old coolant properly.
- Refit the drains and fill with the coolant your handbook specifies.
- Run the engine to working temperature with the heater on, let it cool and top up.
- Clean the radiator fins while you are there (Perkins lists this every 500 hours or 1 year).
Tools: Drain tray, Hose, Coolant tester
Transmission and hydraulic oil and filter change
Transmission · when needed
Old oil wears the gearbox, shuttle clutches and hydraulic pump. The MF workshop manual gives the fill, but no source used gives the interval or oil type, so check your handbook. Change the filters with the oil every time.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission oil | 1 | ≈62 L mechanical shuttle or ≈74 L power shuttle; type: check your handbook | check your handbook |
| Hydraulic oil filters | 2 | Main hydraulic filter. Power-shuttle tractors also have transmission filter 3792287M1; tractors with a trailer brake valve take 3619712M1. Check which yours has | 3616579M1 |
Step-by-step
- Park on level ground, lower the linkage and any loader fully, stop the engine, take the key out and chock the wheels.
- With the engine off, work the lift and spool levers to relieve any trapped hydraulic pressure.
- Let the oil cool to warm, not hot, then drain it. Wear gloves.
- Change the filters, cleaning around each one first.
- Refit the plugs and fill with the specified oil to the correct level.
- Run the engine, work the hydraulics through their full travel, lower everything, stop and recheck the level.
Tools: Large drain tray (80 L), Spanners, Filter wrench, Pump or funnel
Front axle and final drive oil change (4WD)
Front axle · when needed
The MF workshop manual gives the fills, but no source used gives the interval or oil type, so check your handbook.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Axle oil | 1 | Housing ≈5.5 L plus ≈0.9 L per final drive; type: check your handbook | check your handbook |
Step-by-step
- Park on level ground, lower implements, stop the engine, take the key out and chock the wheels.
- Turn the front wheels so each final drive plug is where the handbook shows for draining.
- Drain the axle housing and both final drives.
- Refit the drain plugs and fill each to its level plug.
- Wipe the axle clean so you can spot leaks later.
Tools: Drain tray, Spanners, Oil pump or squeeze bottle
Oils, fluids and capacities
| System | Oil or spec | Capacity |
|---|---|---|
| Engine | Perkins 1104 4.4 L 4-cylinder turbo diesel | |
| Engine oil | Check your handbook for the grade and spec. | ≈7.5 L (MF 5400 workshop manual) |
| Coolant | ≈16.6 L (MF 5400 workshop manual). Type: check your handbook. | |
| Valve clearances | 0.35 mm (0.013 in) inlet and exhaust (Perkins 1104D handbook). Tier 2 1104C engines: check your handbook. | |
| Transmission | Check your handbook | ≈62 L with mechanical shuttle; ≈74 L with power shuttle |
| Front axle (4WD) | Check your handbook | ≈5.5 L |
| Front final drives (4WD), each | Check your handbook | ≈0.9 L |
| Brakes | Hydraulic wet disc brakes; check your handbook for the fluid | — |
| Fuel tank | Diesel | ≈150 L, plus ≈50 L optional extra tank |
| Air conditioning | Refrigerant | 1,550 g |
Specifications
| Engine power | 95 hp (70.8 kW) at 2,200 rpm |
| PTO power | 80 hp (59.7 kW) claimed; 82.6 hp (61.6 kW) tested |
| Weight | ≈3,935–4,221 kg (8,675–9,305 lb), depending on build |
| Tyres (common) | Front 10.00-16, rear 18.4R38 |
| Tyre pressures | Check your handbook |
| Linkage | Category II |
| Rear lift (at 610 mm) | 3,175 kg (7,000 lb) |
| Hydraulics | Open centre 57 L/min (100 L/min optional); closed centre optional; 200 bar |
| PTO | 540/1000 rpm independent; 540E/1000 optional |
Known problems
Tier 2 and Tier 3 engines take different filters
Agriline sells separate kits for Tier 2 and Tier 3 engines and for standard and Hi-Vis bonnets. Check your engine and bonnet before ordering.
Engine name differs between sources
Agriline lists the 5455 engine as 1104C-44/44T for both Tier 2 and Tier 3, while another supplier lists a 1104D-E44TA for the Tier 3 (2008 on). Check the engine plate.
Two transmission oil fills
The workshop manual gives ≈62 L with the mechanical shuttle and ≈74 L with the power shuttle. Fill to the level mark, not by volume alone.
Engine oil interval is not clear-cut
The Perkins handbook lists the oil change at both 250 hours and 500 hours or 1 year. Use your MF handbook; if in doubt, change at 250 hours.
Repair guides
- Identify your engine, gearbox and serial number before buying parts (Easy, 30 minutes): Wrong filter, gasket or oil quantity arrives; parts lists give two or more numbers for the same model; the transmission takes a different amount of oil from the book figure.
- Power shuttle will not drive or flashes a code (Autotronic 5) (Specialist, 1 hour of owner checks; calibration by the dealer): Reverse lamp flashing on the dash, no drive forward or reverse, harsh or slow shuttle changes, or the clutch pedal does not take up drive smoothly.
- Electronic warning or fault code: owner checks before calling the dealer (Specialist, 30–60 minutes of checks): Warning lamp or code on the dash, a function (shuttle, PTO, linkage, 4WD) stops working, or several faults appear at once.
- Wet brakes: pedal adjustment and bleeding (Moderate, 2–3 hours): Spongy or low pedal, pedals at different heights, pulling to one side with pedals latched, or poor braking after a master cylinder or pipe has been disturbed.
- Overheating: water pump and thermostat (Perkins 1104) (Moderate, 2–4 hours): Temperature gauge climbing, coolant loss, coolant weeping behind the fan, or slow warm-up.
- Head gasket replacement (Perkins 1104C) (Hard, 8–12 hours): Coolant loss with no visible leak, white smoke, pressurised coolant hoses, oil in the coolant.
- Misfire or will not start after running dry: injectors and priming (Perkins 1104) (Moderate, 1–3 hours): Misfire, smoke, loss of power, or no start after running out of fuel or changing a filter.
- Linkage will not lift, lifts slowly or drops (owner checks) (Moderate, 1–2 hours): Linkage will not lift a load it used to, lifts slowly when hot, creeps down with the engine stopped, or hunts up and down.
- PTO will not engage, cuts out or flashes a code (Specialist, 30–60 minutes of owner checks): PTO lamp flashing, PTO switches on but the shaft does not turn, PTO cuts out under load, or it will not engage on the low-speed (economy) setting.
- Four-wheel drive will not engage or will not disengage (Moderate, 1–2 hours of checks): 4WD lamp on but no front drive, 4WD stays in when switched off (tyre scrub and tight steering on hard ground), or 4WD comes in by itself.
- 4WD front axle: swivel (kingpin) and hub bearing play, oil leaks (Hard, 1 hour to check; a day or more per side to rebuild): Front wheel moves when rocked, clunk when changing direction, oil on the inside of a front wheel, uneven tyre wear, or a growl from a front hub.
- Cab air conditioning not cooling (owner checks) (Moderate, 1 hour of checks; regassing by an air-con specialist): Air con blows warm, cools only at speed, the compressor clutch does not click in, the fan is weak, or the cab windows mist.
- Slow cranking, no start or battery not charging: starter and alternator (Moderate, 1–3 hours): Starter clicks but does not turn, slow cranking, battery warning lamp stays on, battery flat every morning, or a whine from the alternator.
- Valve lash check: which figure for a Tier 2 (1104C) and a Tier 3 (1104D) 5455 (Moderate, 2–3 hours): Ticking from the top of the engine, loss of power, hard starting, or at the valve check interval.
The full step-by-step guides are in Farmyard Workshop once you add your tractor.
Parts list with genuine part numbers
Agriline MF 5455 category pages (OEM numbers quoted as suitable-for); Perkins engine, Tier and serial breaks in notes; plus earlier rows from the site service schedule
Engine service
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Oil filter | 1447031M2 | 1 | Spin-on, 175 mm long (Perkins 2654407); Agriline lists it for the 5455 |
| Inner (safety) air filter | 3901465M1 | 1 | Agriline lists this for the 5455; 3901465M2 also listed |
| Outer air filter | 3901464M1 | 1 | Steep-nose bonnet; pairs with inner 3901465M1. Standard-bonnet Tier 2 tractors take outer 3901475M1 with inner 3901476M1 |
| Rocker cover gasket | 4224954M1 | 1 |
Fuel
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel filter | 4226599M1 | 1 | Listed by a parts seller for 1104D-E44T engines in the 5455 (Perkins 2656F843); Agriline notes its Tier 2 kit filter replaces the complete canister. Check yours |
| Primary filter / water separator element | 4226708M1 | 1 | Tier 3 tractors. Tier 2 tractors have a single cartridge, 4224811M1, that replaces the whole canister |
Cooling
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Water pump, gear driven, with gasket | 4226951M91 | 1 | genuine number per Agriline; also 4226775M91; serial break applies |
| Perkins water pump | 4225069M91 | 1 | genuine number per Agriline; also 4226913M91, U5MW0194 |
| Thermostat housing with 82C thermostat | 4224784M1 | 1 | genuine number per Agriline; also 4225038M1, 4225430M1 |
| Fan belt 1300 mm | 3780603M91 | 1 | genuine number per Agriline |
| Fan belt 1450 mm (Tier 2, steep nose bonnet) | 3619084M91 | 1 | genuine number per Agriline |
| Viscous fan drive (from serial P174008) | 3783351M1 | 1 | genuine number per Agriline |
| Water filler cap | 3800373M1 | 1 | genuine number per Agriline |
| Radiator fan cowl | 3800434M5 | 1 | genuine number per Agriline; also 3800434M6 |
Transmission and hydraulics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Hydraulic oil filters | 3616579M1 | 2 | Main hydraulic filter. Power-shuttle tractors also have transmission filter 3792287M1; tractors with a trailer brake valve take 3619712M1. Check which yours has |
Clutch
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Clutch kit 330 mm (cover, 23-spline plate) | 4306911M1 | 1 | genuine number per Agriline; also 3798073M1, 379749M1 |
| Torsion damper 302 x 41.5, 26 splines | 3792448M2 | 1 | genuine number per Agriline; also 3010238X1, 3799604M12 |
| Wet clutch plate (Dynashift) | 3619155M1 | 5 | genuine number per Agriline |
| Clutch pilot bearing 25 x 52 x 15 | 339581X1 | 1 | genuine number per Agriline |
| Clutch pedal switch | 4295389M4 | 1 | genuine number per Agriline |
| Clutch pedal rubber top | 1626321M2 | 1 | genuine number per Agriline |
| Clutch pedal bush | 3385604M1 | 1 | Up to serial P194057; genuine number per Agriline |
| Clutch pedal spring | 3786148M1 | 1 | genuine number per Agriline |
Brakes
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Handbrake disc 164 mm, sintered | 3795093M1 | per side | genuine number per Agriline |
| Handbrake actuator 170 mm | 3716920M91 | 1 | genuine number per Agriline |
| Wet brake disc 342 mm | 3617651M91 | per side | genuine number per Agriline; some 5425 serials only |
| Brake piston 270 mm | 3790013M4 | per side | genuine number per Agriline |
| Brake piston O-ring, small | 3382190M1 | per side | genuine number per Agriline |
| Brake piston O-ring, large | 3382189M1 | per side | genuine number per Agriline |
| Friction disc | 3616400M7 | per side | genuine number per Agriline |
| Handbrake cable 1080 mm | 3778581M2 | 1 | genuine number per Agriline |
| Brake master cylinder | 3384685M2 | 1 | genuine number per Agriline; also 3384685M3 |
| Brake master boost cylinder (serial N093031 to S066037) | 3786100M2 | 1 | genuine number per Agriline |
| Master cylinder seal kit, 3 pipe | 1810832M91 | 1 | genuine number per Agriline |
| Master cylinder seal kit, 4 pipe | 1810833M91 | 1 | genuine number per Agriline |
Front axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| King pin | 3429319M1 | per side | genuine number per Agriline |
| King pin seal 45.5 x 64.7 x 6 | 3429317M1 | per side | genuine number per Agriline |
| Front axle bush | 3713930M1 | per axle | genuine number per Agriline; also 3810480M1 |
| Axle spindle thrust washer kit | 1810572M92 | per axle | genuine number per Agriline |
| Wheel bearing kit | 1810320M91 | per side | genuine number per Agriline |
| Outer halfshaft seal | 3785500M1 | 2 | genuine number per Agriline; also 84295344 |
| Half shaft seal 45 x 64 x 25 | 3765756M1 | 2 | genuine number per Agriline |
| 4WD front pinion bearing 40 x 80 x 23 | 1440642X1 | 1 | genuine number per Agriline |
| 4WD differential bearing 65 x 100 x 23 | 391339X1 | 2 | genuine number per Agriline |
| Driveshaft bearing 35 x 72 x 42.9 | 3386985M1 | 1 | genuine number per Agriline |
| Propshaft seal 55 x 82 x 16.5 | 3428942M1 | 2 | genuine number per Agriline |
| 4WD propshaft coupling, rear | 3380056M2 | 1 | genuine number per Agriline |
| 4WD propshaft coupling, front | 3384857M4 | 1 | genuine number per Agriline |
Steering
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Track rod end M28 x 1.5 | 3599679M92 | 2 | genuine number per Agriline |
| Track rod end LH/RH M18 x 1.5 | 3764027M1 | 2 | genuine number per Agriline; also 3764027M2 |
| Steering joint 175.5 mm | 3426312M1 | 2 | genuine number per Agriline; also 1966125C1, 061352R1, 3909379M1 |
| Steering joint 114 mm (power steering cylinder) | 1695045M91 | 1 | genuine number per Agriline |
| Steering cylinder seal repair kit (2WD) | 3443433M92 | 1 | genuine number per Agriline; also 3443433M93 |
| Steering wheel | 3809661M1 | 1 | genuine number per Agriline |
PTO
| Part | Part number | Qty | Notes |
|---|---|---|---|
| PTO output shaft 1000 rpm | 3790903M2 | 1 | genuine number per Agriline |
| PTO output shaft 540 rpm | 3790902M1 | 1 | genuine number per Agriline |
| PTO switch | 3619445M2 | 1 | genuine number per Agriline |
| PTO stop switch | 4284626M1 | 1 | genuine number per Agriline |
| Front PTO switch | 4271352M1 | 1 | genuine number per Agriline |
| 4WD output shaft seal kit | 3384503M1 | 1 | genuine number per Agriline; also 1808472M91 |
Hitch
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Levelling box | 4307220M91 | 1 | genuine number per Agriline |
| Drop arm pin | 3618522M2 | 2 | genuine number per Agriline |
| Lower link ball Cat 2/2 (quick release) | 3042429M1 | 2 | genuine number per Agriline; also 3617876M1 |
| Lower link ball and guide cone Cat 2/2 | 3042426M1 | 2 | genuine number per Agriline |
| Hook lock repair kit Cat 3 | 3903314M91 | 2 | genuine number per Agriline |
| Hook lock repair kit Cat 2 | 3904032M91 | 2 | genuine number per Agriline |
| Quick release weld-on hook end Cat 2 (to 150 hp) | 3903954M91 | 2 | genuine number per Agriline |
| Automatic stabiliser with float | 4271701M91 | 2 | genuine number per Agriline |
| Adjustable stabiliser | 3615707M91 | 2 | genuine number per Agriline |
| Pick-up hitch hook | 3771816M1 | 1 | genuine number per Agriline |
| Front linkage top link | 4281474M2 | 1 | genuine number per Agriline |
Electrics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Ignition switch with two keys | 32804146 | 1 | genuine number per Agriline |
| Starter motor 2.8 kW | 1860093M2 | 1 | genuine number per Agriline; also 234987A1, 3763362M92 |
| Starter motor 3 kW (Mahle) | 6106496M92 | 1 | genuine number per Agriline |
| Starter motor 4.2 kW gear reduction (Iskra) | 3823621M91 | 1 | genuine number per Agriline; also 3777247M1, 3823621M95/M96 |
| Alternator 14V 80A | 3821974M91 | 1 | genuine number per Agriline |
| Alternator 14V 120A (Perkins) | 3821978M91 | 1 | genuine number per Agriline; also 4279541M92; 120A Mahle also 4287014M4 |
| Glow plug | 4224813M1 | per cylinder | genuine number per Agriline |
| Glow plug 134.5 mm | 4226560M1 | per cylinder | genuine number per Agriline; also 4227143M1, 4227450M1 |
| Headlight switch | 3713142M1 | 1 | genuine number per Agriline |
| Indicator and light switch | 3713669M4 | 1 | genuine number per Agriline |
| Hi/Lo switch (gear stick) | 3786097M1 | 1 | genuine number per Agriline |
| Differential lock switch | 4271348M2 | 1 | genuine number per Agriline |
| Parking brake switch | 3780395M2 | 1 | genuine number per Agriline |
| Headlight, LH dip | 3788221M91 | 1 | genuine number per Agriline |
| Work lamp, single beam cab mount | 3786664M91 | 1 | genuine number per Agriline; bulb Agriline 9353 |
| Work lamp, twin beam with bracket | 3786666M91 | 1 | genuine number per Agriline |
| Engine oil pressure sensor (Tier 3) | 4226184M91 | 1 | genuine number per Agriline |
| Engine speed sensor (Tier 3) | 4226444M91 | 1 | genuine number per Agriline |
| Relay 20A | 3615652M1 | 1 | genuine number per Agriline |
Cab
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Cab glass, front window green tint (5425-5470) | 4274322M1 | 1 | genuine number per Agriline |
| Cab glass, opening front window | 4272738M1 | 1 | genuine number per Agriline |
| Cab glass, rear window | 4272760M1 | 1 | genuine number per Agriline |
| Wiper motor 12V | 3715610M1 | 1 | genuine number per Agriline |
| Gas stay, front/rear window | 3902140M1 | 1 | genuine number per Agriline |
| Rear window hinge | 3804698M2 | 1 | genuine number per Agriline |
Sources
- Valve lash 0.20 mm inlet / 0.45 mm exhaust, cold, Perkins 1103/1104 industrial engine specifications (manual p.18)
- Valve lash 0.35 mm inlet and exhaust, Perkins 1104D operation and maintenance manual p.23
- Oil filter 1447031M2 for the 5455 (UK specialist)
- Primary fuel filter 4226708M1 (Tier 3) for the 5455 (UK specialist)
- Tier 2 single fuel cartridge 4224811M1 (UK specialist)
- Outer air filter 3901464M1, steep-nose 5455 (UK specialist)
- Hydraulic filter 3616579M1 for the 5455 and 6480 (UK specialist)
- Transmission filter 3792287M1, power shuttle (UK specialist)
- Rocker cover gasket 4224954M1 for the 5455 (UK specialist)
- Years, power, fuel tank, hydraulics, lift, linkage, PTO, weight, tyres
- Engine type (Perkins 1104 4.4 L), rated speed, Tier II
- Capacities: engine oil, coolant, transmission, front axle, final drives, fuel, air con (MF 5400 workshop manual)
- MF 5400 operator's manual 4346732M2 (preview): hydraulic flow 57 and 100 L/min
- Perkins 1104D operation and maintenance manual SEBU8172: maintenance interval schedule, valve lash
- Filter kits by engine tier and bonnet type for the 5455
- Inner air filter 3901465M1/M2 fitment includes the 5455
- Fuel filter 4226599M1 / 2656F843 for 1104D-E44T engines in the 5455
- Agriline model pages (engine, cooling, clutch, brakes, front axle and steering, electrical, linkage, cab, transmission/PTO as available)
- Agriline MF 5455 clutch page
More from Massey Ferguson.