New Holland T5.110 / T5.120 service schedule

1. Wipe each grease nipple clean.
2. Grease the rear three-point hitch, the tow hitch and the front axle system as your handbook shows.
3. Every 300 hours also grease the steering knuckle and king pin; every 1,200 hours or annually the wheel hubs.
4. Wipe off excess grease.

Tools: Grease gun, Rags

1. Stop the engine, let it cool and take the key out.
2. Blow or wash the condenser, transmission cooler and aftercooler clean from the engine side outwards.
3. Clean the cab air filters.

Tools: Compressed air or soft hose, Soft brush, Dust mask

1. Stop the engine, take the key out and look at each belt for cracks, glazing and fraying.
2. Check the tension as your handbook shows.
3. Replace any belt that is worn, and replace them at the interval anyway.

Tools: Torch, Belt tension gauge or handbook method

1. Stop the engine and take the key out. Never run the engine with the filter out.
2. Open the housing, take out the element and clean the housing with a damp cloth.
3. At the replacement interval fit a new element; at the cleaning interval clean it as your handbook describes.
4. Close the housing and check the hoses.

Tools: Torch, Damp cloth

1. Park on level ground, lower the linkage and implements, stop the engine, take the key out and chock the wheels.
2. Clean round the filters and have a tray ready for oil.
3. Remove the old filters, oil the seals of the new ones and fit them.
4. Run the engine, work the hydraulics through their full travel and recheck the oil level and for leaks.

Tools: Drain tray, Filter wrench, Rags, Gloves

1. Warm the engine, park on level ground, lower the linkage, loader and any implement, stop the engine, take the key out and chock the wheels.
2. Let it stand a few minutes. Hot oil burns, so wear gloves.
3. Remove the sump plug and let the oil drain fully.
4. Remove the filter, check the old seal came off with it, and wipe the filter head clean.
5. Oil the new filter seal and fit it hand-tight.
6. Refit the plug and fill with the oil your handbook specifies to the full mark.
7. Run the engine for a minute, check for leaks, stop it and recheck the level.

Tools: Drain tray (15 L), Filter wrench, Spanner for the sump plug, Funnel, Rags, Gloves

1. Stop the engine, take the key out and chock the wheels. Keep naked flames away.
2. Clean round the filter heads before opening anything.
3. Drain any water into a container, then remove the old filters.
4. Fit the new filters with clean seals and bleed the system as your handbook describes.
5. Start the engine and check for leaks.

Tools: Container for fuel, Filter wrench, Rags, Gloves

1. Check and tighten the wheel nuts to the torque in your handbook.
2. Once a year drain any water and sediment from the fuel tank into a container.

Tools: Torque wrench, Drain container

1. Stop the engine and take the key out.
2. Open the filter covers and remove the elements, wearing a dust mask.
3. Fit the new filters, including the recirculation filter, and check the covers seal.

Tools: Screwdriver, Dust mask

1. Park on level ground, lower the linkage and implements, stop the engine, take the key out and chock the wheels.
2. Let hot oil cool a while, then drain it from the drain plug and refit the plug.
3. Fill with the specified oil to the level mark, run the engine, work the hydraulics through their full travel and recheck the level.
4. Fit new lift and oil filters if they are due or have not been changed recently.

Tools: Drain tray, Spanners, Pump or funnel, Gloves

1. Park on level ground, lower implements, stop the engine, take the key out and chock the wheels.
2. Drain the front axle and the final drives and refit the plugs.
3. Fill each to its level plug or mark.

Tools: Drain tray, Spanners, Oil pump or squeeze bottle

1. Only work on a cold engine. Open the cap slowly to let pressure out.
2. Drain the radiator into a tray and dispose of the old coolant properly.
3. Fill with the coolant your handbook specifies.
4. Run the engine to working temperature with the heater on, let it cool and top up.

Tools: Drain tray, Hose, Coolant test strips

1. Have the receiver-drier changed and the system recharged by an air-conditioning specialist.

Tools: Dealer job