New Holland T6010 / T6020 service schedule
New Holland T6000 · 2007–2012
Covers the New Holland T6010 / T6020 (Delta / Plus / Elite, 4-cylinder).
Every maker's service job for the New Holland T6010 / T6020, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.
Track your T6010 / T6020 for freeVersions: Synchro Command 12x12 or 24x24; Dual Command 24x24; Electro Command 16x16
Service intervals
| Job | When |
|---|---|
| Grease points (50-hour list) | every 50 hours |
| Engine oil and filter change | every 600 hours or every year |
| Hydraulic and transmission oil filters change | every 600 hours |
| Air cleaner outer element change | every 600 hours |
| Fuel pre-filter and fuel filter change | every 600 hours |
| 4WD axle and hub oil levels | every 600 hours |
| Cab air filters change | every 1,200 hours or every year |
| Transmission, rear axle and hydraulic oil and filters change | every 1,200 hours or every year |
| 4WD differential and hub oil change | every 1,200 hours or every year |
| Coolant drain, flush and refill | every 1,200 hours or every 2 years |
| Air cleaner inner element change | every 1,200 hours or every 2 years |
| Valve tappet clearance check | every 1,200 hours or every 2 years |
| Fuel injectors clean and reset | every 1,800 hours |
| Air conditioning service | every 3 years |
Service jobs and parts
Grease points (50-hour list)
Chassis · every 50 hours
The handbook greases all fittings at the 50-hour service. Grease 2WD front hubs daily in bad conditions.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Grease | 1 | EP2 grease, NLGI 2, NH 710 A. Aztec Oils match: VOLCATEC LITHIUM EP 2 | check your handbook |
Step-by-step
- Park level, lower the linkage, stop the engine, take the key out and chock the wheels.
- Oil all pivots. Grease both lift rods (turnbuckle type) and the external lift cylinder where fitted.
- 2WD axle: trunnion pin, wheel spindles, right-hand steering arm and outer steering parts; pack the hub caps with grease.
- Standard 4WD axle: front and rear trunnion pins. SuperSteer axle: front and rear trunnion pins. Suspended axle: Panhard rod pivot and suspension arm.
- All 4WD axles: steering cylinders. Suspended and SuperSteer axles: drive shaft universal joint. Dynamic mudguards where fitted.
- Wipe off surplus grease.
Tools: Grease gun, Oil can, Rag
Engine oil and filter change
Engine · every 600 hours or every year
The handbook gives 600 hours, or every 12 months if the tractor does fewer than 600 hours a year. Below -12 °C or in hard work, change the oil at 300 hours (filter at 600). Fuel with 0.5-1.0% sulphur means 300 hours and 1.0-1.3% means 150 hours. The 4-cylinder engine takes 10 L with the filter.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Engine oil | 1 | 15W-40. NH 330 H, 10 L with filter. Aztec Oils match: EMPROTEC SHPD-X 15W-40 | check your handbook |
| Engine oil filter | 1 | From the New Holland dealer lube chart for the T6010 / T6020; it replaces 2854749 | 84228488 |
Step-by-step
- Warm the engine, park level, stop it and take the key out. Let very hot oil cool to warm.
- Remove both drain plugs at the rear of the sump (one each side), drain the oil and refit them.
- Clean round the filter, unscrew it and throw it away. Clean the face, oil the new seal, screw it on until it touches and then a further 3/4 to 1 turn. Do not overtighten.
- Fill with oil through the filler. Do not go above MAX.
- Run at idle for 3 minutes, stop, check for leaks, wait 5 minutes and check the level is between MIN and MAX.
Tools: Drain tray (15 L), Spanners for two drain plugs, Filter wrench, Funnel, Gloves
Hydraulic and transmission oil filters change
Hydraulics · every 600 hours
The handbook changes the hydraulic and transmission filters at the 600-hour service. Which filters you have depends on the pump: some tractors have a suction filter, others a pressure and a charge filter.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Hydraulic oil filter (suction) | 1 | From the New Holland dealer lube chart for the T6010 / T6020 (used with open-centre hydraulics and 12x12, and on Plus models) | 84248043 |
| Hydraulic oil filter (pressure) | 1 | From the same chart | 84226263 |
| Hydraulic oil filter (CCLS suction) | 1 | From the same chart for CCLS hydraulics | 84226260 |
Step-by-step
- Lower the linkage, stop the engine, take the key out and chock the wheels. The filters are under the right-hand side of the floor.
- Move the hydraulic levers with the engine off to relieve pressure.
- Clean round each filter, remove and throw away the old ones. Check which types your tractor has before ordering.
- Clean the faces, oil the new seals and fit the new filters.
- Run the engine, work the hydraulics, check for leaks and check the oil in the sight glass.
Tools: Filter wrench, Drain tray, Rag
Air cleaner outer element change
Engine · every 600 hours
The handbook changes the outer element at the 600-hour service, or when the warning lamp lights, and checks all intake connections then.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Air cleaner outer element | 1 | From the New Holland dealer lube chart for the T6010 / T6020; 87704244 is the other number listed | 82034604 |
Step-by-step
- Stop the engine and take the key out.
- Remove the outer element and throw it away. Clean inside the housing with a damp cloth without disturbing the inner element.
- Fit the new element and close the housing.
- Check the clamps between the air cleaner, turbo, intercooler and inlet manifold, and the exhaust aspirator joints. Do not overtighten.
Tools: Damp lint-free cloth on a probe, Screwdriver for clamps
Fuel pre-filter and fuel filter change
Fuel · every 600 hours
The handbook changes the fuel pre-filter (water separator) and the fuel filter at the 600-hour service.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Fuel pre-filter (water separator) | 1 | The dealer lube chart lists 84171722 for the T6010 / T6020; the dealer's fuel filter page 84565884 replaces it and lists the T6010 | 84565884 |
| Fuel filter | 1 | Check your handbook or dealer for the main filter on the 4-cylinder tractor | check your handbook |
Step-by-step
- Clean the area first: dirt in the injection system does damage.
- Pre-filter: remove the drain plug and sensor wire, open the drain knob and drain into a container. Unscrew the filter and dispose of it properly.
- Lightly oil the new gasket, screw the filter on until it touches and then a further turn, to 15 N·m. Do not overtighten. Refit the sensor wire.
- Change the main fuel filter the same way.
- Bleed the fuel system as the handbook shows, then start the engine and check for leaks.
Tools: Container, Torque wrench or filter wrench, Clean rag
4WD axle and hub oil levels
Front axle · every 600 hours
The handbook checks the front axle and hub levels at the 600-hour service.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission oil for top-up | 1 | UTTO tractor transmission oil, NH 410 B. Aztec Oils match: AGRITEC UTTO | check your handbook |
Step-by-step
- Park level and stop the engine.
- Remove the axle level/filler plug: oil should reach the bottom of the hole. Top up if needed.
- Turn each wheel so the hub plug is at 3 o'clock, remove it, check the oil reaches the bottom of the hole and top up.
Tools: Spanner, Oil pump or squeeze bottle
Cab air filters change
Cab · every 1,200 hours or every year
The handbook changes the cab filters every 1,200 hours or 12 months.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Cab air filter (outer) | 2 | From the New Holland dealer lube chart: 87726675 on Plus and Elite, 87726696 on Delta only | 87726675 |
| Cab recirculation filter (inner) | 1 | From the same chart | 87726699 |
Step-by-step
- Switch the blower off.
- Outer filters: turn the quick-release fastener, remove the cover and element, wipe the chamber and fit the new element with the arrow pointing up. Handle the rubber edge carefully.
- Inner filter: loosen the captive screws, remove the cover and element, wipe the chamber and fit the new one with the arrow towards the rear of the tractor.
Tools: Damp lint-free cloth
Transmission, rear axle and hydraulic oil and filters change
Transmission · every 1,200 hours or every year
The handbook changes the shared oil every 1,200 hours or 12 months, and says change the hydraulic and transmission filters before refilling. The quantity depends on the gearbox and axle: 55 to 65.5 L.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission and hydraulic oil | 1 | UTTO tractor transmission oil. NH 410 B; 58 L (12x12), 58.5 L (24x24) or 55 L (16x16) light duty axle; 65 L, 65.5 L or 62 L heavy duty. Aztec Oils match: AGRITEC UTTO | check your handbook |
| Hydraulic oil filters | 1 | As the 600-hour task; change all the filters your tractor has | 84248043 |
Step-by-step
- Run the engine and work the hydraulics until the oil is warm. Park level, lower the linkage, stop the engine, set the parking brake and chock both sides.
- Let very hot oil cool to warm and wear gloves. Remove the drain plug and drain all the oil, then refit the plug.
- Change the hydraulic and transmission filters (600-hour task) before refilling.
- Refill through the filler. Run the engine, work the hydraulics and fully raise the linkage. Stop, wait 5 minutes, check for leaks and fill to between MIN and MAX in the sight glass.
Tools: Drain tray (70 L), Large spanner, Filter wrench, Pump
4WD differential and hub oil change
Front axle · every 1,200 hours or every year
The handbook changes the 4WD differential and planetary hub oil every 1,200 hours or 12 months.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Transmission oil | 1 | UTTO tractor transmission oil. NH 410 B; 9.0 L differential, 1.25 L per hub (3.0 L with hub brakes). Aztec Oils match: AGRITEC UTTO | check your handbook |
Step-by-step
- Park level and set the parking brake.
- Drain the differential, refit the plug, and fill until oil reaches the bottom of the level/filler hole.
- Drain each hub with its plug at the bottom, then turn the plug to 3 o'clock and fill to the bottom of the hole.
Tools: Drain tray, Spanners, Oil pump
Coolant drain, flush and refill
Cooling · every 1,200 hours or every 2 years
The handbook drains, flushes and refills with 50% ethylene glycol antifreeze every 1,200 hours or two years, because the inhibitor wears out.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Antifreeze | 1 | NH 900 A, 50% with water; 23 L with cab, 21 L without | check your handbook |
Step-by-step
- Let the engine cool. With a thick cloth, turn the cap slowly to the first stop and let pressure escape.
- Drain and flush the system as your handbook shows.
- Refill with 50% antifreeze and 50% water, run the engine warm, let it cool and top up. Use an approved pressure cap.
Tools: Drain tray (30 L), Hose, Antifreeze tester, Thick cloth
Air cleaner inner element change
Engine · every 1,200 hours or every 2 years
The handbook changes the inner element every 1,200 hours or two years.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Air cleaner inner element | 1 | From the New Holland dealer lube chart for the T6010 / T6020 | 87682992 |
Step-by-step
- Remove the outer element, then the inner one, and cover the outlet with a clean cloth.
- Wipe the housing and fit the new inner element at once, then a new or the current outer element, and close the housing.
Tools: Damp lint-free cloth
Valve tappet clearance check
Engine · every 1,200 hours or every 2 years
The handbook checks the tappet clearance at the 1,200-hour or two-year service, with the engine cold. On the 4-cylinder engine you balance No. 1 cylinder first, then No. 4.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| Rocker cover gasket | 1 | check your handbook | check your handbook |
Step-by-step
- Work on a cold engine. Take the key out.
- Remove the ventilation tube bolt, ease the tube off and take off the rocker cover.
- Turn the crankshaft to balance No. 1 cylinder's valves and adjust the valves the handbook marks; then balance No. 4 and adjust the rest.
- Set inlet to 0.25 ± 0.05 mm and exhaust to 0.51 ± 0.05 mm, then refit the cover.
Tools: Feeler gauges, Spanners, Socket set
Fuel injectors clean and reset
Fuel · every 1,800 hours
The handbook lists injector cleaning and resetting every 1,800 hours. Removing them needs special tools, so the handbook recommends a dealer.
Step-by-step
- Book the tractor in with your dealer.
- Never check for fuel leaks with your hand: high-pressure diesel can go through skin. Use cardboard and wear gloves and eye protection.
Tools: Dealer or injection specialist
Air conditioning service
Cab · every 3 years
The handbook says have the receiver-drier replaced and the system checked by a dealer every three years or three seasons.
| Part | Qty | Notes | Part number |
|---|---|---|---|
| A/C receiver-drier | 1 | Dealer fits; check your handbook | check your handbook |
Step-by-step
- Book it with a dealer or A/C specialist: refrigerant must not be released and can cause frostbite.
- Never open the system or put heat near it yourself.
Tools: Dealer with A/C equipment
Oils, fluids and capacities
| System | Oil or spec | Capacity |
|---|---|---|
| Engine | 4.5 L (4,485 cc) 4-cylinder turbo diesel (FPT NEF 4.5 L); T6010 74 kW (101 hp), T6020 82 kW (112 hp) | |
| Engine oil | 15W-40. NH 330 H, API CH-4 / ACEA E5 (10W-30 to NH 324 H in cold weather); handbook names Ambra Mastergold HSP | 10 L with filter |
| Coolant | 50% ethylene glycol antifreeze to NH 900 A (Ambra Agriflu), 50% water. 23 L with cab, 21 L without | |
| Valve clearances | Inlet 0.25 ± 0.05 mm (0.010 in), exhaust 0.51 ± 0.05 mm (0.020 in), cold | |
| Engine oil | 15W-40, NH 330 H, API CH-4 / ACEA E5 | 10 L with filter |
| Transmission, rear axle and hydraulics (shared) | UTTO tractor transmission oil. NH 410 B, M2C 134D, API GL4, ISO VG 32/46, SAE 10W-30 (Ambra Multi G) | Light-duty axle: 58 L (12x12), 58.5 L (24x24), 55 L (16x16). Heavy-duty axle: 65 L, 65.5 L, 62 L |
| 4WD front axle differential | NH 410 B (as transmission) | 9.0 L |
| 4WD front hubs, each | NH 410 B (as transmission) | 1.25 L (3.0 L for hubs with brakes) |
| Brake fluid | Ambra LHM Brake, NH 610 A (mineral fluid) | To the mark |
| Grease | EP2 grease, NLGI 2 lithium-calcium, NH 710 A (Ambra GR9) | - |
| Coolant | 50% ethylene glycol antifreeze to NH 900 A, 50% water | 23 L with cab, 21 L without |
| Fuel tank | Diesel | 180 L |
Specifications
| Advertised power | T6010 74 kW (101 hp); T6020 82 kW (112 hp) |
| Cylinders and capacity | 4 cylinders, 4,485 cc |
| Engine oil capacity | 10 L with filter (6-cylinder T6030 to T6070: 15 L) |
| Remote oil draw | Do not add more than 20 L above the top mark for remote cylinders |
Known problems
4-cylinder only
This entry is for the 4-cylinder T6010 and T6020. The 6-cylinder T6030, T6050 and T6070 take 15 L of engine oil and are in the T6030 entry.
Several hydraulic filter types
The hydraulic filters depend on the pump and gearbox. Look under the right-hand floor and order by serial number.
Mineral brake fluid
The brakes use LHM mineral fluid (NH 610 A). DOT brake fluid will ruin the seals.
Remote oil draw
Do not add more than 20 L above the top mark for remote cylinders, and check the level with rams extended.
Fault codes: T6000 and T7000 series: what the first digits of a fault code mean
Dot matrix display system fault codes
| Code | Meaning | What to do |
|---|---|---|
| 0xxx | General fault (listed for the T6010 only) | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 1xxx | Electronic draft control (rear hitch) | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 2xxx | Transmission | Note the full code. If the tractor is disabled, call your dealer with the code. Check the parking brake, clutch pedal and shuttle lever first (see the action codes P, CP and N). |
| 3xxx | Engine | Note the full code and check the oil and coolant levels. Call your dealer with the code. |
| 4xxx | Rear electronic remote valves | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 45xx | Front electronic remote valves (T7000) | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 5xxx | Rear PTO system | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 6xxx | Front wheel drive | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 7xxx | Rear differential lock | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 8xxx | Front PTO system | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 9xxx | Front 3-point hitch | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 10xxx | Front axle suspension | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 14xxx | Instrument cluster / instrument panel electrics (T6010 only) | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 15xxx | Fast Steer system | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
| 16xxx | Cab automatic temperature control (T7000 only) | Note the symbol and the full code and call your dealer; the code needs reading with their tools. |
Fault codes: T6000 (T6010 to T6070) dot matrix warning symbols
Warning and alarm symbols on the dot matrix display
| Code | Meaning | What to do |
|---|---|---|
| Engine coolant temperature too high | Critical, red STOP light and alarm | Stop as soon as it is safe. Idle briefly, then stop. Let it cool; check coolant level and clean the radiator and grille. If you cannot find the cause, dealer. |
| Engine oil pressure low | Critical, red STOP light | Stop at once. Check the oil level and for leaks. Do not run it if the level is correct and the warning stays: dealer. |
| Transmission / power steering oil pressure low | Critical, red STOP light | Stop at once. Check the transmission oil level and for leaks, then dealer. |
| Transmission oil temperature too high | Critical, red STOP light | Stop, idle to cool, check the oil cooler for chaff and mud and the oil level. Dealer if it returns. |
| Hydraulic system charge pressure low | Warning light with dot matrix symbol (the manual's table is unclear on its colour) | Stop as soon as possible and check the hydraulic oil level and filter indicator. Dealer if it stays. |
| Air brake pressure low | Amber, non-critical | Do not travel until the air pressure has built up. If it will not build up, dealer. |
| Engine air filter blocked | Amber, non-critical | Clean or replace the air filter element at the next safe stop. |
| Brake fluid level low | Amber, non-critical | Check the brake fluid reservoir level. Top up only with the fluid the handbook names, and have a dealer find where it is going. |
| Hydraulic oil filter blocked | Amber, non-critical | Change the hydraulic oil filter. A blocked filter may only show when the oil is warm. |
| Transmission oil filter blocked | Amber, non-critical | Change the transmission oil filter. |
| Water in fuel | Amber, non-critical | Drain the fuel water separator until clean fuel runs. |
Fault codes: T6010 to T6070 (cab) fuse box and relays
Fuses and relays
| Code | Meaning | What to do |
|---|---|---|
| Fuse 1 | 10 A: Interior and courtesy lights | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 2 | 25 A: Cigar lighter and power studs | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 3 | 10 A: Air conditioning clutch | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 4 | 10 A: Accessory sockets | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 5 | 30 A: Blower motor | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 6 | 10 A: Radio KAM and worklamp ECU | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 7 | 20 A: Main lights and hazard switch | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 8 | 20 A: Starter switch | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 9 | 25 A: Loader | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 11 | 10 A: Front and rear windscreen wiper | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 12 | 10 A: Wiper switch and rear wiper park | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 13 | 15 A: Stoplamps | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 14 | 15 A: Main light switch and turn signal | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 15 | 20 A: Stoplamp switch, hydraulic trailer brake and pedal latch | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 16 | 15 A: Pneumatic trailer brake | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 17 | 25 A: Accessory sockets | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 18 | 15 A: Blower motor and seat | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 20 | 10 A: Radar socket, transmission diagnostic socket, ADIC keypad, radar, backup alarm | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 21 | 15 A: Grid heater, water-in-fuel sensor, brake fluid level switch | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 22 | 15 A: Sidelamps right-hand | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 23 | 15 A: Sidelamps left-hand | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 24 | 10 A: Illumination | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 25 | 15 A: Dipped beam headlamps | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 26 | 15 A: Main beam headlamps | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 27 | 15 A: Front worklamps (hood) | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 28 | 15 A: ECU worklamp | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 29 | 30 A: ECU worklamp | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 30 | 15 A: Rear lower worklamps | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 31 | 15 A: ECU worklamp | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 32 | 30 A: Flasher unit | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 33 | 25 A: Diagnostic connector and engine ECU | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 34 | 10 A: Instrument cluster | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 35 | 10 A: SCM (small control module) | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 36 | 10 A: Instrument cluster ignition | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 37 | 15 A: Transmission ignition | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 38 | 10 A: SCM, switch panel, ground speed PTO switch, rear PTO warning lamp, PTO brake | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 39 | 10 A: Seat | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 40 | 10 A: Radio | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 43 | 10 A: Starter switch (run position) | Replace with the same rating only. This protects a safety or road-use circuit: if it blows again, have the wiring checked before you use the tractor on the road. |
| Fuse 44 | 25 A: Front implement power socket | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Fuse 45 | 25 A: Front ignition and 8 amp socket | Replace with the same rating only. If it blows again, find the fault before fitting anything bigger. |
| Relay 1 | Relay: Front windscreen wiper module | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 2 | Relay: Rear window wiper module | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 3 | Relay: Ignition relay | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 4 | Relay: Side/tail lights and illumination | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 5 | Relay: Starter | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 6 | Relay: Blower motor | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 7 | Relay: Dipped beam headlamps | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 8 | Relay: Stoplamps | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 9 | Relay: Main beam headlamps | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 10 | Relay: Pneumatic trailer brake supply | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 11 | Relay: Hydraulic trailer brake supply | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 12 | Relay: Stoplamps switch feed and pneumatic brakes | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 13 | Relay: Engine cold start advance (mechanical engines only) | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 14 | Relay: Reverse alarm | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 15 | Relay: Air conditioner clutch relay feed | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 16 | Relay: Electronic remote valve power (16x16 transmissions only) | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 19 | Relay: Front lower worklamps (hood) | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 20 | Relay: Rear lower worklamps | Swap only with a same-type relay for a quick test; otherwise dealer. |
| Relay 21 | Relay: Electrical supply | Swap only with a same-type relay for a quick test; otherwise dealer. |
Parts list with genuine part numbers
New Holland T6010 Tier 3 Plus (01/07-08/13) parts catalogue, mycnhstore.com GB
Maintenance filters
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Engine oil filter, spin-on 95mm x 171mm M27x2 | 84228488 | 1 | Every 600 h; Wear part |
| Engine oil filter, FleetPro | 92048690FP | 1 | Wear part |
| Fuel filter, spin-on with water separator | 84171722 | 1 | Before engine s/n 710159; Wear part |
| Fuel filter, spin-on with water separator | 84526251 | 1 | After engine s/n 710158; Wear part |
| Fuel filter 75.8mm x 172mm M16x1.5 | 84565884 | 1 | Engine fuel filter page, before engine s/n 710158; Wear part |
| Fuel prefilter, cleanable 350 micron | 84328598 | 1 | Every 600 h; Wear part |
| Air filter, outer/primary 387.5mm | 84493217 | 1 | Standard equipment; Wear part |
| Air filter, outer/primary 387.5mm | 87704244 | 1 | With pre-cleaner; Wear part |
| Air filter, inner/secondary | 87682992 | 1 | Every 1200 h; Wear part |
| Engine breather, oil vapour separator | 2852027 | 1 | Every 600 h |
| Transmission breather 20mm x 142mm | 47133085 | 1 | Every 600 h |
| Hydraulic lift breather | 9636958 | 1 | Every 600 h |
| Hydraulic/transmission oil filter, spin-on 97mm x 240mm | 84226258 | 1 | 63 l/min fixed pump; 113 l/min CCLS pump from 01-Dec-2009; Wear part |
| Hydraulic/transmission oil filter, spin-on 136mm x 244mm | 84248043 | 1 | 80 l/min fixed pump; Wear part |
| Hydraulic/transmission oil filter 93.2mm x 264mm | 84226260 | 1 | 113 l/min CCLS pump up to 30-Nov-2009; Wear part |
| Hydraulic/transmission oil filter 119.4mm x 295.4mm | 84226263 | 1 | 113 l/min CCLS pump from 01-Dec-2009; larger filter after first 50 h; Wear part |
| Hydraulic oil filter element and gasket (Argo) | 47617638 | 1 | CCLS pump up to 21-Feb-2016; Wear part |
| Hydraulic oil filter 148mm x 268mm 32 micron (Argo) | 47715391 | 1 | CCLS pump from 22-Feb-2016; Wear part |
| Cab filter, fresh air, low-profile roof | 87311207 | 2 | Every 1200 h or 12 months; Wear part |
| Cab filter 359x109x10mm, low-profile roof | 87726696 | 2 | Var. 332618; Wear part |
| Cab filter heating/conditioning, low-profile roof | 87311194 | 2 | Up to s/n Z8BD17935; Wear part |
| Cab filter fresh air 380x130x49mm, low-profile roof | 87726695 | 2 | From s/n Z8BD17936; Wear part |
| Cab filter, inner recirculation cartridge | 92247265 | 1 | Wear part |
| Cab filter, inner recirculation cartridge | 87302687 | 1 | Up to s/n Z8BD17935; Wear part |
| Cab filter heating/conditioning, high-profile roof | 82034664 | 2 | Up to s/n Z8BD17935; Wear part |
| Cab filter fresh air 550x100x64mm, high-profile roof | 87726675 | 2 | From s/n Z8BD17936; Wear part |
| Cab filter 527x77x10mm, high-profile roof | 87726694 | 2 | From 18-Jun-2009; Wear part |
| Receiver-drier, air conditioning | 87374420 | 1 | Every 1200 h or two years |
Belts, starter and alternator
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fan belt, V-belt 28.48mm x 1550mm 8 rib | 4899178 | 1 | Every 300 h or annually; Wear part |
| Air conditioner compressor belt, flat 14mm x 990mm 4 rib | 87710661 | 1 | Wear part |
| Starter motor | 87318375 | 1 | Before 18-Apr-2007 |
| Starter motor (Iskra) | 87653219 | 1 | From 18-Apr-2007 |
| Starter motor 12V 4.2kW | 84151331 | 1 | From s/n Z9BD02999 |
| Alternator 120A | 87361082 | 1 | Before 07-Jun-2007 |
| Alternator 120A (Iskra) | 87652087 | 1 | From 07-Jun-2007 |
| Alternator 12V 120A with pulley | 84141452 | 1 | From 28-Feb-2010 |
| Starter motor cover | 82039109 | 1 | |
| Alternator cover M6 | 87533425 | 2 |
Fuses and relays
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuse 10A mini red | 87522597 | AR | |
| Fuse 15A mini blue | 87524877 | AR | |
| Fuse 20A mini yellow | 10401190 | AR | |
| Fuse 250A blade pink | 84174069 | AR | From 18-Jun-2010 |
| Fuse 250A strip type pink | 82023624 | AR | Up to 17-Jun-2010 |
| Starter motor relay | 82030798 | AR | |
| Battery disconnect relay 14V 190A | 87392809 | 1 |
Hydraulic pumps and power steering
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Hydraulic pump piston 45 cc | 5198694 | 1 | Before 01-Dec-2009 |
| Hydraulic pump | 84164091 | 1 | From 01-Dec-2009 |
| Hydraulic pump gear 32 cc | 5192659 | 1 | |
| Hydraulic pump 16.76 cc | 87603409 | 1 | From 28-Feb-2008 |
| Hydraulic pump | 5192657 | 1 | Before 28-Feb-2008 |
| Hydraulic pump 19.69 cc | 87314177 | 1 | |
| Power steering kit, fast steer, CL.3 4WD axle | 84198336 | 1 | |
| Power steering kit, fast steer, 2WD | 87303173 | 1 | Var. 332631 |
| Steering column hydraulic valve | 87525763 | 1 | Var. 331631 |
| Power unit, steering column, 4WD with Supersteer axle | 82991560 | 1 | |
| Steering valve, standard steer, 4WD | 82001471 | 1 | Before 18-Jun-2008 |
| Power steering kit, 4WD CL.3 axle | 84198317 | 1 | |
| Power steering kit 125cc, heavy-duty front axle | 84266839 | 1 | |
| Power steering kit, heavy-duty front axle | 47137771 | 1 | |
| Power steering kit, hydraulic transmission | 47137781 | 1 | |
| Power steering kit, fast steer, CL.3 axle | 87303174 | 1 | |
| Power steering kit, hydraulic transmission | 84266840 | 1 |
Engine - sump and breather
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Engine oil pan kit | 2853793 | 1 | |
| Oil pan gasket set | 4894295 | 1 | Wear part |
| O-ring M23.47 | 2853728 | 2 | |
| Drain plug M22x1.5 | 4894139 | 2 | |
| Oil separator | 4895935 | 1 | |
| Breather gasket | 2852028 | 1 | Wear part |
Engine - cylinder head
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Cylinder head kit, T6010 | 4895790 | 1 | Check engine P/N on engine ident plate |
| Cylinder head 4 cylinder, T6010-T6020 | 2856017 | 1 | Check engine P/N on engine ident plate |
| Exhaust valve | 4895188 | 4 | |
| Inlet valve | 4895187 | 4 | |
| Valve collet | 4895183 | 16 | |
| Valve stem seal | 4895347 | 8 | |
| Valve spring | 4895215 | 8 | |
| Valve spring retainer | 4895184 | 8 | |
| Exhaust valve seat | 4897178 | 4 | |
| Inlet valve seat | 4897179 | 4 | |
| Cylinder head gasket 1.25mm | 2830919 | 1 | Choose thickness by piston protrusion; Wear part |
| Cylinder head gasket 1.15mm | 2830920 | 1 | Choose thickness by piston protrusion; Wear part |
| Cylinder head bolt M12x1.75x73 | 4892861 | 4 |
Engine - rocker cover
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Valve cover | 2852032 | 1 | |
| Valve cover gasket | 2852033 | 4 | Wear part |
| Baffle | 2830775 | 1 | |
| Oil filler cap | 4895202 | 1 | |
| Filler cap sealing ring | 4895296 | 1 |
Engine - pistons
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Piston and rings kit, standard | 8094740 | 4 | |
| Piston and rings kit, 0.4mm oversize | 87317252 | 4 | |
| Piston pin 38mm | 4892712 | 4 | |
| Piston rings kit, standard | 87582179 | 4 | Wear part |
| Piston rings kit, +0.4 | 87316944 | 4 | Wear part |
Engine - fuel system
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel injection pump, Tier 2 engine | 2855292 | 1 | Supplier 9520A220W |
| Fuel injection pump, Tier 3 engine | 2855962 | 1 | Supplier 9320A980W |
| Fuel shut-off solenoid 12V | 83981012 | 1 | |
| Fuel injector | 2854071 | 4 | Check engine P/N on ident plate; Wear part |
| Fuel injector | 2855965 | 4 | Check engine P/N on ident plate; Wear part |
| Injector sealing washer | 2854033 | 4 | Wear part |
| Fuel filter assembly kit | 2853543 | 1 | Wear part |
| Fuel filter sensor M10 | 2853540 | 1 | Before engine s/n 710158; Wear part |
| Fuel filter sensor M14x2 | 2853585 | 1 | After engine s/n 710159; Wear part |
| Fuel filter head | 2830455 | 1 | Wear part |
| Fuel lift pump | 2830266 | 2 | Qty as printed |
| Fuel pump O-ring | 2830156 | 1 | |
| Fuel pump | 2830122 | 1 | |
| Fuel pipe, T6010 | 2853789 | 1 | |
| Injection pipe | 2855941 | 1 | |
| Fuel pipe O-ring | 4894095 | 2 |
Engine - turbo, oil pump, cooling
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Turbocharger | 4895271 | 1 | Check engine P/N on ident plate |
| Turbocharger | 2856752 | 1 | Check engine P/N on ident plate |
| Turbo gasket 0.5mm | 4895133 | 1 | Wear part |
| Engine oil pump | 2830913 | 1 | |
| Oil pump gasket | 2830972 | 1 | Wear part |
| Oil seal M70x100x12.5 | 4890832 | 1 | |
| Crankshaft speed sensor | 2853552 | 1 | |
| Water pump | 2852114 | 1 | |
| Water pump sealing ring | 2852047 | 1 | |
| Thermostat housing | 2854354 | 1 | Wear part |
| Thermostat | 2853135 | 1 | Wear part |
| Thermostat gasket | 2853133 | 1 | Wear part |
| Fan pulley | 2853304 | 1 | |
| Fan hub | 4892426 | 1 | |
| Fan hub bearing | 4892732 | 1 | |
| Fan 5 blades 510.5mm | 81868399 | 1 | |
| Viscous fan hub | 81862862 | 1 |
Radiator and hoses
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Radiator 5 row | 87306757 | 1 | |
| Radiator cap | 87306788 | 1 | |
| Air-con condenser | 82035720 | 1 | Up to C6540 |
| Air-con condenser | 84156148 | 1 | From D6540 |
| Coolant expansion tank | 82019588 | 1 | |
| Expansion tank filler cap | 82022744 | 1 | |
| Radiator hose upper | 82030134 | 1 | |
| Radiator hose lower | 82030135 | 1 |
Air cleaner
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Air cleaner assembly, standard | 82034601 | 1 | |
| Air cleaner assembly with pre-cleaner | 82034610 | 1 | |
| Air filter restriction indicator | 82029621 | 1 | Wear part |
| Air cleaner cover | 87301829 | 1 | |
| Air cleaner dust valve | 87301825 | 1 | |
| Air intake duct, T6010 | 87389109 | 1 |
Fuel tank
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Fuel tank | 87490435 | 1 | From 25-Sep-2009 to 24-Oct-2013 |
| Fuel tank filler cap | 82012210 | 1 | |
| Fuel gauge sender | 84417843 | 1 | |
| Fuel tank filler neck | 87554848 | 1 |
Brakes
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Rear brake disc | 5191497 | 2 | Var. 331248; Wear part |
| Rear brake piston | 5191494 | 2 | |
| Brake piston seal square | 5165512 | 2 | |
| Brake piston seal quad | 5191498 | 2 | |
| Parking brake disc 126x190x4.5 | 47127225 | 4 | Wear part |
| Parking brake pad 3.1mm | 5199607 | 2 | Wear part |
| Parking brake pad 4.2mm | 5199788 | 3 | Wear part |
| Parking brake pad 9mm | 47127226 | 1 | Wear part |
| Parking brake lever | 47127313 | 1 |
PTO
| Part | Part number | Qty | Notes |
|---|---|---|---|
| PTO housing | 47131252 | 1 | |
| PTO gear | 5197561 | 1 | |
| PTO valve spring | 47123788 | 1 | |
| PTO cover | 87673377 | 1 | |
| PTO clutch piston | 83999379 | 1 | |
| PTO brake band 19mm | 47124034 | 1 | Wear part |
| PTO brake band 23mm | 87391136 | 1 | Wear part |
| PTO housing, clutch support | 87518133 | 1 |
Lift and linkage
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Lift housing, Plus version | 47126511 | 1 | |
| Lift housing, Delta version | 87384891 | 1 | |
| Rockshaft bush RH | 5186406 | 2 | |
| Rockshaft bush LH | 5186405 | 2 | |
| Lift cylinder 86mm bore | 5131998 | 1 | |
| Lift piston | 5132000 | 1 | |
| Piston guide ring | 5125941 | 1 | |
| Rockshaft | 5117187 | 1 | |
| Lift arm RH | 5173542 | 1 | |
| Lift arm LH | 5183176 | 1 | |
| Rockshaft seal 55x70x8 | 5159078 | 2 | |
| Piston rod 30mm x 174mm | 5121221 | 1 |
Steering and front axle
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Steering cylinder LH | 47130812 | 1 | Var. 330413 |
| Steering cylinder RH | 47130813 | 1 | Var. 330413 |
| Steering cylinder seal kit | 5192826 | 1 | Var. 330413; Wear part |
| Steering cylinder piston | 5192819 | 1 | Var. 330413 |
| Steering cylinder piston rod | 47125713 | 1 | Var. 330413 |
| Steering cylinder 356mm | 87521950 | 1 | Var. 330409 etc. |
| Steering cylinder seal kit | 84121150 | 1 | Var. 330409 etc.; Wear part |
| 2WD heavy-duty front hub assembly | 81863773 | 2 | Var. 330407 |
| Front hub bearing assembly | 81812262 | 2 | Var. 330407 |
| Front hub bearing assembly | 81812305 | 2 | Var. 330407 |
| Front hub roller bearing | 81812303 | 2 | Var. 330407 |
| Front hub bearing cup | 81812302 | 2 | Var. 330407 |
| Front hub cap | 81812309 | 2 | Var. 330407 |
| 2WD standard front hub assembly | 81823160 | 2 | Var. 330406 |
| Front hub bearing assembly | 82971753 | 2 | Var. 330406 |
| Front hub bearing assembly | 82964614 | 2 | Var. 330406 |
| Front hub cap | 81802363 | 2 | Var. 330406 |
| Wheel bolt 1/2-20 x 1 3/4 | 81816580 | 6 | Var. 330406 |
Battery and electrics
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Battery isolator switch | 87392866 | 1 | Var. 330798 |
| Negative battery cable | 87324239 | 1 | |
| Positive battery cable 1290mm | 87324238 | 1 | |
| Battery isolator relay 30 sec | 87639044 | 1 | |
| Battery isolator relay 4 min | 87691156 | 1 | |
| Battery cable fuse 250A | 82033972 | 2 | |
| Fuse holder 30A | 76045724 | 2 | |
| Fuse holder 250A | 82027575 | 2 |
Bulbs
| Part | Part number | Qty | Notes |
|---|---|---|---|
| Bulb H4 12V 60/55W | 87283179 | AR | |
| Bulb H1 12V 55W | 86616248 | AR | |
| Bulb H3 12V 55W | 14151590 | AR | |
| Bulb PY21W | 14148090 | AR | |
| Bulb P21/5W | 14144690 | AR | |
| Bulb W5W | 14144190 | AR |
Sources
- Lubrication and maintenance chart: items and intervals (T6010-T6070 operator's manual, page 4-10)
- Lubricant and coolant specifications (page 4-9)
- 600-hour service: engine oil change period, 10 L (4-cylinder) and 15 L (6-cylinder) capacity (page 4-31)
- Valve clearance, 4-cylinder and 6-cylinder balancing; 1,200-hour services
- Capacities table: T6010 / T6020 engine oil 10 L, coolant 23 L and 21 L, transmission figures, fuel tank 180 L
- Engine specification: T6010 and T6020 4 cylinders, 4,485 cm3
- Filters for the T6010 / T6020: oil 84228488, pre-filter 84171722, air 82034604 / 87704244 / 87682992, hydraulic 84226260 / 84248043 / 84226263, cab 87726675 / 87726699 (New Holland dealer lube chart)
- Fuel filter 84565884 replaces 84171722, lists the T6010 (New Holland dealer)
- Production years 2007-2012, 4.5 L four-cylinder
- T6010 Tier 3 Plus model page, selected assemblies
More from New Holland.