Valtra T153, T163e, T183, T203, T213 service schedule

Valtra T series (T3) · 2012–2014 (Eurol pages)

Covers the Valtra T153, T163e, T183, T203, T213 (T3 Versu and Direct).

Every maker's service job for the Valtra T153, T163e, T183, T203, T213, counted in hours, with the oils, filters and parts each one needs. Add your tractor to Farmyard Workshop and it works out what's due from your hours and dates, and keeps the service history.

Track your T153, T163e, T183, T203, T213 for free

Versions: Versu (powershift); Direct (stepless)

Service intervals

JobWhen
Grease all nipplesevery 50 hours
Engine oil and filter changeevery 500 hours or every year
Front PTO oil changeevery 500 hours
Hydraulic oil and filter changeevery 1,000 hours or every year
Front differential oil changeevery 1,000 hours or every year
Front hub reduction oil changeevery 1,000 hours or every year
Transmission oil changeevery 2,000 hours or every 2 years
Coolant changeevery 2,000 hours or every 2 years

Service jobs and parts

Grease all nipples

Chassis · every 50 hours

Eurol lists the grease points at 50 hours. Grease point positions: check your handbook.

PartQtyNotesPart number
Grease1Grade: check your handbookcheck your handbook
Step-by-step
  1. Wipe each nipple, pump in grease until a little shows, and wipe off the excess.
  2. Do the steering, front axle, linkage, PTO shaft and any other nipples your handbook shows.

Tools: Grease gun

Engine oil and filter change

Engine · every 500 hours or every year

Eurol's advice page, quoting the maker's figures, gives the engine oil change at 500 hours or 12 months, with a level check every 10 hours. With more than 5% biodiesel, Eurol shows 250 hours. The oil and filter are changed together.

PartQtyNotesPart number
Engine oil1Grade: check your handbook (the Eurol page names none). 19 Lcheck your handbook
Engine oil filter1Genuine number not found in any source: check your handbook or parts bookcheck your handbook
Step-by-step
  1. Warm the engine, stop it and put the tray under the sump. Remove the drain plug and let the oil drain fully.
  2. Refit the plug with a good washer. Unscrew the old filter, wipe the sealing face, oil the new seal and screw the filter on by hand.
  3. Fill to the top mark on the dipstick, run for a few minutes, stop, check for leaks and recheck the level.

Tools: Drain tray (20 L), Filter wrench, Funnel

Front PTO oil change

PTO · every 500 hours

Front PTO housing oil. Eurol shows a change at 500 hours.

PartQtyNotesPart number
Front PTO oil1Grade: check your handbook (the Eurol page names none). 2 Lcheck your handbook
Step-by-step
  1. Run the tractor briefly to warm the oil, then park level.
  2. Remove the drain plug, drain, refit and fill to the level plug or sight mark.
  3. Check for leaks.

Tools: Drain tray, Funnel

Hydraulic oil and filter change

Hydraulics · every 1,000 hours or every year

Eurol shows 1,000 hours or 12 months for the hydraulic oil (62 L), with a level check every 10 hours. The oil and its filter are changed together.

PartQtyNotesPart number
Hydraulic oil1Grade: check your handbook (the Eurol page names none). 62 Lcheck your handbook
Hydraulic filter1Genuine number not found in any source: check your handbook or parts bookcheck your handbook
Step-by-step
  1. Warm the oil, park level, lower all implements and stop the engine.
  2. Drain the hydraulic oil, change the filter as your handbook shows, and refit the plug.
  3. Refill to the correct level, run the pumps for a few minutes and recheck.

Tools: Drain tray (70 L), Filter wrench, Funnel

Front differential oil change

Front axle · every 1,000 hours or every year

Eurol shows 1,000 hours or 12 months, with a level check every 500 hours.

PartQtyNotesPart number
Front differential oil1Grade: check your handbook (the Eurol page names none). 7.4 L (industrial axle)check your handbook
Step-by-step
  1. Park level and warm the oil if you can.
  2. Remove the drain plug and let the oil drain fully, then refit it.
  3. Refill through the filler or level plug to the correct level and check for leaks.

Tools: Drain tray, Funnel, Spanners

Front hub reduction oil change

Front axle · every 1,000 hours or every year

Eurol shows 1,000 hours or 12 months, with a level check every 500 hours.

PartQtyNotesPart number
Front hub reduction oil1Grade: check your handbook (the Eurol page names none). 2 L each (industrial axle)check your handbook
Step-by-step
  1. Park level and warm the oil if you can.
  2. Remove the drain plug and let the oil drain fully, then refit it.
  3. Refill through the filler or level plug to the correct level and check for leaks.

Tools: Drain tray, Funnel, Spanners

Transmission oil change

Transmission · every 2,000 hours or every 2 years

Eurol shows 2,000 hours or 24 months for the transmission, with a level check every 10 hours. The page lists no filter for it.

PartQtyNotesPart number
Transmission and hydraulic oil1Grade: check your handbook (the Eurol page names none). 65 Lcheck your handbook
Step-by-step
  1. Warm the oil by working the tractor, park level, stop and lower all implements.
  2. Drain the oil from the drain plugs into a large tray, and change the filters as your handbook shows.
  3. Refill to the correct level with the engine off, run for a few minutes and recheck the level.

Tools: Large drain tray (100 L), Filter wrench, Funnel or pump

Coolant change

Cooling · every 2,000 hours or every 2 years

Eurol shows a coolant change at 2000 hours or 24 months. 30 L.

PartQtyNotesPart number
Coolant1Type: check your handbook. 30 L.check your handbook
Step-by-step
  1. Let the engine cool fully before opening the cap.
  2. Drain the radiator and block, flush, refit the drains and refill with the correct mix.
  3. Run to temperature, let it cool and top up.

Tools: Drain tray, Hose clamp pliers

Oils, fluids and capacities

SystemOil or specCapacity
EngineAGCO Power (Sisu) 6-cylinder turbo diesel: 66AWI (T153) or 74AWI (T163e, T183, T203, T213)
Engine oilCheck your handbook. Eurol's page gives no grade or spec.19 L (Eurol)
Coolant30 L. Type: check your handbook.
Valve clearancesCheck your handbook.
Engine oilCheck your handbook19 L
TransmissionCheck your handbook65 L
Hydraulic systemCheck your handbook62 L
Front PTO housingCheck your handbook2 L
Front hub reductions (industrial axle)Check your handbook2 L
Front differential (industrial axle)Check your handbook7.4 L
Cooling systemCheck your handbook30 L

Specifications

Source typeLubricant-advisor data (Eurol, quoting the maker's figures); no operator's handbook read. Lower confidence.
NoteT3 HiTech is already on the site as valtra-t3-hitech

Fault codes: Valtra Direct transmission / PTO codes (E and A)

Transmission, PTO and pedals

CodeMeaningWhat to do
E001Foot throttle sensor out of rangeCheck the pedal plug; call your dealer.
E004Hand throttle sensor out of rangeCall your dealer.
E007Left and right brake pedal sensors disagreeCheck the pedals are not sticking. Have the brakes checked before road use.
E009 / E0104WD pressure switch signal wrong (engine off / on)Call your dealer.
E011-E013Diff-lock switch or pressure signal faultAvoid using diff-lock; call your dealer.
E014-E016, E047Cruise SET/UP/DOWN switch stuck or shortedDo not use cruise; call your dealer.
E020 / E021PTO safety or main valve gives no feedbackStop using the PTO and call your dealer.
E023PTO switch readings disagreeCheck the switch is fully in position.
E041-E046PTO pressure switch, valve stuck open, clutch low pressure, or output speed signal faultStop using the PTO and call your dealer.
E066 / E067Transmission ECU supply voltage below 9 V / above 16 VCheck battery and charging.
E068 / E069Sensor supply voltage too low / too highCall your dealer.
E070-E072Overcurrent on a clutch or main valve circuitCall your dealer.
E080 / E081Clutch pedal angle sensor voltage too high / lowCheck the pedal; call your dealer.
E085-E088Transmission pressure or filter differential pressure faultsCheck the transmission oil level and filter; call your dealer.
E091Transmission oil temperature excessiveStop, idle, and let it cool; check the oil level when cool.
E092 / E093Oil temperature sensor signal too high / too lowCall your dealer.
E094-E102Clutch valve coil faults (forward high/low, reverse)Call your dealer.
A311Gearbox oil temperature sensor B14 reads over 150 CTreat as a sensor fault unless the tractor is genuinely hot; call your dealer.
A312Gearbox oil temperature impossible (below -50 C)Sensor or wiring fault; call your dealer.
A313 / A314 / A315Accelerator or clutch pedal sensor out of range or deviatingCheck pedal plugs; call your dealer.

Parts list with genuine part numbers

Valtra T153V tractor (T3 series, Versu) AGCO parts book (no serial range in book title; T153D Direct is a separate book)

Brakes

PartPart numberQtyNotes
Parking brake cylinder assemblyACV023308A1
Parking brake seal set (S1)V34008700
Parking brake wire L=1005V32841820
Brake leverACV0301750
Brake springV31841400
Brake master cylinder - boosterV367906101
Brake master cylinder - booster (with front axle brakes)V37479900
Brake pedal, rightV36618600
Brake pedal, leftV36616100
Pedal forkV36795800
Pedal springV37210400
Pedal needle roller bearingV70038200
Pedal safety switch 12VV33558700
Pedal rubber sealV36847600
Brake slave cylinder (mineral oil)V367989101
Actuating disc kitV34127300
Repair kit, friction/intermediate plateV34665000
Brake disc 9.5 inchV34127100Wear part
Brake disc, intermediate 9.5 inchV34127200Wear part
Brake counter plateV33709110
SpringV34665100
SpringV34665300
ForkV34665400
Ball 7/8 inchV412960
Front axle brake piston assembly (745/509)V37962700
Front axle brake disc (745/509)V37963400Wear part
Front axle brake friction plate (745/509)V37963500Wear part
Front axle brake disc (745/509)V37963600Wear part
Front axle brake supporting ringV37962400
Front axle brake supporting ringV37962900
Front axle brake springV37963000
Front axle brake bleed screwV37962300

Clutch pedal and transmission

PartPart numberQtyNotes
Clutch pedalV36661900
Clutch pedal angle sensorV34253500
Clutch pedal springV33540700
Clutch pedal springV34265800
Transmission/hydraulic filter cartridgeACV07693701
Hydraulic filter seal kitV37944100
Hydraulic filter housingACV0252590
Lubrication oil filter sensorV37943100
Hydraulic oil filter sensorV37943200
Valve seal setV36224900
Valve seal setV39444800
Transmission oil coolerV63965200

Engine

PartPart numberQtyNotes
Engine oil filterV836662580Wear part
Oil cooler, oil to water typeV836859699
Oil cooler sealV836862235
Oil pressure valve gasketV836322190
Engine air filter, main cartridgeV836862573Wear part
Engine air filter, safety cartridgeV836862574Wear part
Air filter assemblyV34939900
Air filter gasket L=960V33572300
Air filter sensor 65 barV34654000
Fuel filter (pre-filter)V837079555Wear part
Fuel filter (primary)V837079556Wear part
Fuel pre-filter assemblyV837073963
Fuel filter primary element kitV837073857
Fuel filter water alarmV837074054
Fuel filter O-ringV837079628
Fuel filter O-ringV614601125
Water pump assemblyV8368740551
Water pump multi-ribbed pulleyV837073927
Water pump ball bearingV610060124
Water pump bearingV610063044
Water pump shaftV836866628
Water pump shaft sealV614102636
Water pump impellerV836846303
Water pump gasketV837073981
Water pump gasketV836864471
Starter motor 12V 4.3 kW (Bosch)V8368734571
Starter solenoidV836879293
Starter gasketV836879294
Starter brush holder kitV836879297
Alternator 150 amp 14VV8366733441
Alternator 150 amp with pulley (alternative)ACV0204490
Serpentine belt PK6 6PK894V39517600Wear part

Front axle and steering (Dana 745)

PartPart numberQtyNotes
Steering cylinder (Dana 745/508 and 509)V362489001
Steering cylinder seal setV36335200
Tie rod and ball joint assemblyV362490002
Tie rodV37017400
Axial jointV37017500
Front axle 745/508V37438100
Front axle 745/509 with brakesV37477100
Axle housing, leftV37955800
Axle housing, rightV37955910
Axle bearing bushV31790300
Front axle shaft sealVKH3780
Front axle housing O-ringVKH3784

Hydraulics

PartPart numberQtyNotes
Tandem hydraulic pump S1 28+19V361862101
Hydraulic pump 115 l/minV37359700
Hydraulic pump 160 l/min (optional)V37377600
Hydraulic pump seal set (S1)V34354700
Safety valve 23 MPaV33442800
Suction strainerV32556300
Suction strainer (pump cover)V63123000
Proportional valve, power lift 75 l/minV36828400
Proportional valve seal kitV35699800
Solenoid valveV32477910
Quick coupling seal setV31887200

Rear linkage

PartPart numberQtyNotes
Lower link, right, Cat 3 L=940V354714201
Lower link, left, Cat 3 L=940V354715201
Lower link repair kitV39047400
Lower link joint 37mmV33223900
Lower link guide cone Cat 3/2V32677700
Lower link ball joint Cat 3 (64/37.4)V32773300
Lower link ball joint Cat 3/2 (64/28.4)V30683300
Top link, ball end L=635-880 M33x3V33392120
Top link turnbuckle M33x3V33392210
Top link rod clampV37214200
Lift cylinder, left 110x40x185V373696001
Lift cylinder, right 110x40x185V373697001
Lift cylinder seal kitV37785100
Lift cylinder pistonV37784900
Lift cylinder rodV33359900

Cab mirrors and seat

PartPart numberQtyNotes
Side mirror assembly, arm and mirrorV36451700
Side mirror armV36307100
Side mirrorV36512800
Mirror replacement glassV30581300
Mirror mountingV30581400
Driver's seat assembly MSG85A/731V363939001
Seat upper partV34149800
Armrest, leftV34161000

Sources

Open Farmyard Workshop

More from Valtra.